manualshive.com logo in svg

Texas Instruments Concerto F28M35 Series, Техническое справочное руководство


Поделиться
Скачать
background image

www.ti.com

System Control Registers

273

SPRUH22I – April 2012 – Revised November 2019

Submit Documentation Feedback

Copyright © 2012–2019, Texas Instruments Incorporated

System Control and Interrupts

Table 1-171. M3 to C28 IPC Clear (MTOCIPCCLR) Register Field Descriptions (continued)

Bit

Field

Value

Description

23

IPC24

0

MTOCIPCCLR Flag 24. M3 to C28 core IPC flag 24 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

22

IPC23

0

MTOCIPCCLR Flag 23. M3 to C28 core IPC flag 23 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

21

IPC22

0

MTOCIPCCLR Flag 22. M3 to C28 core IPC flag 22 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

20

IPC21

0

MTOCIPCCLR Flag 21. M3 to C28 core IPC flag 21 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

19

IPC20

0

MTOCIPCCLR Flag 20. M3 to C28 core IPC flag 20 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

18

IPC19

0

MTOCIPCCLR Flag 19. M3 to C28 core IPC flag 19 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

17

IPC18

0

MTOCIPCCLR Flag 18. M3 to C28 core IPC flag 18 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

16

IPC17

0

MTOCIPCCLR Flag 17. M3 to C28 core IPC flag 17 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

15

IPC16

0

MTOCIPCCLR Flag 16. M3 to C28 core IPC flag 16 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

14

IPC15

0

MTOCIPCCLR Flag 15. M3 to C28 core IPC flag 15 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

13

IPC14

0

MTOCIPCCLR Flag 14. M3 to C28 core IPC flag 14 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

12

IPC13

0

MTOCIPCCLR Flag 13. M3 to C28 core IPC flag 13 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

11

IPC12

0

MTOCIPCCLR Flag 12. M3 to C28 core IPC flag 12 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

10

IPC11

0

MTOCIPCCLR Flag 11. M3 to C28 core IPC flag 11 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

9

IPC10

0

MTOCIPCCLR Flag 10. M3 to C28 core IPC flag 10 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

8

IPC9

0

MTOCIPCCLR Flag 9. M3 to C28 core IPC flag 9 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

7

IPC8

0

MTOCIPCCLR Flag 8. M3 to C28 core IPC flag 8 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

6

IPC7

0

MTOCIPCCLR Flag 7. M3 to C28 core IPC flag 8 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

5

IPC6

0

MTOCIPCCLR Flag 6. M3 to C28 core IPC flag 6 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

4

IPC5

0

MTOCIPCCLR Flag 5. M3 to C28 core IPC flag 5 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in MTOCIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the MTOCIPCFLG and STS registers.

Содержание Concerto F28M35 Series
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Concerto F28M35 Series

ABB AC 800M Library Object Style Manual preview
AC 800M
Бренд: ABB Страницы: 120
ABB ABILITY SSC600 Product Manual preview
ABILITY SSC600
Бренд: ABB Страницы: 42
Eaton SC300 Operation Handbook preview
SC300
Бренд: Eaton Страницы: 166
Fagor CNC 8070 Programming Manual preview
CNC 8070
Бренд: Fagor Страницы: 556
RadioMaster POCKET Quick Start Manual preview
POCKET
Бренд: RadioMaster Страницы: 10
Unipower PCM500 Series Operating Manual preview
PCM500 Series
Бренд: Unipower Страницы: 24
Vent-Axia SAC 5 Installation And Wiring Instructions preview
SAC 5
Бренд: Vent-Axia Страницы: 4
Meilhaus Electronic USB-GT Manual preview
USB-GT
Бренд: Meilhaus Electronic Страницы: 19
DMX4ALL DMX-LED-DIMMER X9 HR User Manual preview
DMX-LED-DIMMER X9 HR
Бренд: DMX4ALL Страницы: 14
HobbyKing NanoWii Manual preview
NanoWii
Бренд: HobbyKing Страницы: 16
AMD Am7990 Reference Manual preview
Am7990
Бренд: AMD Страницы: 12
MDT AMI series Technical Manual preview
AMI series
Бренд: MDT Страницы: 51
Teracom TCW112-WD User Manual preview
TCW112-WD
Бренд: Teracom Страницы: 14
Allen-Bradley ProcessLogix 1757-PLX52 Installation Instructions Manual preview
ProcessLogix 1757-PLX52
Бренд: Allen-Bradley Страницы: 24
TRIAC THD S11 SERIES Installation & Maintenance Manual preview
THD S11 SERIES
Бренд: TRIAC Страницы: 7
C.A.P. PPM-4 Quick Start Manual preview
PPM-4
Бренд: C.A.P. Страницы: 2
Truma DIGITAL TIMER CONTROL User Instruction Manual preview
DIGITAL TIMER CONTROL
Бренд: Truma Страницы: 66
Toro LoRa Tempus Air MV User Manual preview
LoRa Tempus Air MV
Бренд: Toro Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды