manualshive.com logo in svg

Texas Instruments Concerto F28M35 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Flash Registers

www.ti.com

514

SPRUH22I – April 2012 – Revised November 2019

Submit Documentation Feedback

Copyright © 2012–2019, Texas Instruments Incorporated

Internal Memory

5.4.1.5

Flash Bank Pump Control Register 1 (FBPRDY)

Figure 5-86. Flash Bank Pump Control Register (FBPRDY)

31

16

Reserved

R-0

15

14

1

0

PUMPRDY

Reserved

BANKRDY

R-0

R-0

R-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 5-90. Flash Bank Pump Control Register (FBPRDY) Field Descriptions

Bit

Field

Value

Description

31-16

Reserved

Reserved

15

PUMPRDY

Pump Ready. This is a read-only bit which allows software to determine if the pump is ready for
flash access before attempting the actual access. If an access is made to a bank when the pump is
not ready, wait states are asserted until it becomes ready.

0

Pump is not ready.

1

Pump is ready, in active power state.

14-1

Reserved

Reserved

0

BANKRDY

Bank Ready. This is a read-only register which allows software to determine if the M3 bank is ready
for Flash access before the access is attempted.

Note:

The user should wait for both the pump and the bank to be ready before attempting an

access.

0

M3 bank is not ready.

1

M3 bank is in active power mode and is ready for access.

5.4.1.6

Flash Bank Pump Control Register 1 (FPAC1)

Figure 5-87. Flash Bank Pump Control Register 1 (FPAC1)

31

27

26

16

Reserved

PSLEEP

R-0

R/W-0x64

15

1

0

Reserved

PMPPWR

R-0

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 5-91. Flash Bank Pump Control Register 1 (FPAC1) Field Descriptions

Bit

Field

Value

Description

31-27

Reserved

Reserved

26-16

PSLEEP

Pump sleep. These bits contain the starting count value for the charge pump sleep down counter.
While the charge pump is in sleep mode, the power mode management logic holds the charge
pump sleep counter at this value. When the charge pump exits sleep power mode, the down
counter delays from 0 to PSLEEP prescaled M3 SYSCLK clock cycles before putting the charge
pump into active power mode.

Note:

The pump sleep down counter uses the same prescaled clock as Bank sleep down counter

which is divided by 2 of input M3 SYSCLK. For a clock operating at 150 Mhz, the following is the
formula used in the obtaining the correct psleep:
PSLEEP = PSLEEP_REQ_ns / 2 / HCLK_period_ns
PSLEEP = 20000/2/6.66 (in decimal)

15-1

Reserved

Reserved

Содержание Concerto F28M35 Series
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Concerto F28M35 Series

Gardena 4040 Operating Instructions Manual preview
4040
Бренд: Gardena Страницы: 100
Danfoss EKC 316A Reference Manual preview
EKC 316A
Бренд: Danfoss Страницы: 16
Gamma Vacuum SPCe User Manual preview
SPCe
Бренд: Gamma Vacuum Страницы: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Бренд: Gamma Страницы: 28
Taco Electronic Solutions iWorx MPU2 Installation Manual preview
iWorx MPU2
Бренд: Taco Electronic Solutions Страницы: 28
Centurion TB-CN2R1 Instruction Manual preview
TB-CN2R1
Бренд: Centurion Страницы: 16
U-Tron 6830-122-C10 Instruction Manual preview
6830-122-C10
Бренд: U-Tron Страницы: 8
Infineon XE166 Series Hardware Manual preview
XE166 Series
Бренд: Infineon Страницы: 28
Continental Instruments CICP1800T Datasheet preview
CICP1800T
Бренд: Continental Instruments Страницы: 2
R-Tec controlR Installation Manual & User Manual preview
controlR
Бренд: R-Tec Страницы: 14
QSC TSC-101-G3 User Manual preview
TSC-101-G3
Бренд: QSC Страницы: 13
H3C WX2880X Installation Manual preview
WX2880X
Бренд: H3C Страницы: 48
Ekinex EK-FF1-TP Quick Start Manual preview
EK-FF1-TP
Бренд: Ekinex Страницы: 4
METRON FD4 Manual preview
FD4
Бренд: METRON Страницы: 34
Ransburg DynaFlow A12233 Service Instruction preview
DynaFlow A12233
Бренд: Ransburg Страницы: 10
Canford TECPRO HS581 Manual preview
TECPRO HS581
Бренд: Canford Страницы: 2
Minebea Intec Maxxis 5 Original Installation Manual preview
Maxxis 5
Бренд: Minebea Intec Страницы: 138
Truma DuoControl horizontal Operating Instructions Manual preview
DuoControl horizontal
Бренд: Truma Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды