manualshive.com logo in svg

Texas Instruments Concerto F28M35 Series, Техническое справочное руководство


Поделиться
Скачать
background image

www.ti.com

System Control Registers

277

SPRUH22I – April 2012 – Revised November 2019

Submit Documentation Feedback

Copyright © 2012–2019, Texas Instruments Incorporated

System Control and Interrupts

Table 1-173. M3 to C28 Core IPC Acknowledge (CTOMIPCACK) Register Field Descriptions (continued)

Bit

Field

Value

Description

25

IPC26

0

CTOMIPCACK Flag 26. C28 to M3 core IPC flag 26 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

24

IPC25

0

CTOMIPCACK Flag 25. C28 to M3 core IPC flag 25 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers

23

IPC24

0

CTOMIPCACK Flag 24. C28 to M3 core IPC flag 24 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

22

IPC23

0

CTOMIPCACK Flag 23. C28 to M3 core IPC flag 23 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

21

IPC22

0

CTOMIPCACK Flag 22. C28 to M3 core IPC flag 22 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

20

IPC21

0

CTOMIPCACK Flag 21. C28 to M3 core IPC flag 21 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

19

IPC20

0

CTOMIPCACK Flag 20. C28 to M3 core IPC flag 20 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

18

IPC19

0

CTOMIPCACK Flag 19. C28 to M3 core IPC flag 19 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

17

IPC18

0

CTOMIPCACK Flag 18. C28 to M3 core IPC flag 18 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

16

IPC17

0

CTOMIPCACK Flag 17. C28 to M3 core IPC flag 17 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

15

IPC16

0

CTOMIPCACK Flag 16. C28 to M3 core IPC flag 16 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

14

IPC15

0

CTOMIPCACK Flag 15. C28 to M3 core IPC flag 15 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

13

IPC14

0

CTOMIPCACK Flag 14. C28 to M3 core IPC flag 14 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

12

IPC13

0

CTOMIPCACK Flag 13. C28 to M3 core IPC flag 13 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

11

IPC12

0

CTOMIPCACK Flag 12. C28 to M3 core IPC flag 12 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

10

IPC11

0

CTOMIPCACK Flag 11. C28 to M3 core IPC flag 11 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

9

IPC10

0

CTOMIPCACK Flag 10. C28 to M3 core IPC flag 10 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

8

IPC9

0

CTOMIPCACK Flag 9. C28 to M3 core IPC flag 9 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

7

IPC8

0

CTOMIPCACK Flag 8. C28 to M3 core IPC flag 8 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

6

IPC7

0

CTOMIPCACK Flag 7. C28 to M3 core IPC flag 7 acknowledge. Writing a ‘1’ to this bit clears the
corresponding bit in CTOMIPCFLG and CTOMIPCSTS to ‘0’. The status of this bit is not readable
in this register – it is readable in the CTOMIPCFLG and STS registers.

Содержание Concerto F28M35 Series
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Concerto F28M35 Series

iCeeO2 C30 Instruction Manual preview
C30
Бренд: iCeeO2 Страницы: 7
Galcon 61 Series Installation And Operating Instructions Manual preview
61 Series
Бренд: Galcon Страницы: 35
D+H RZN 4402-K V2 Original Instructions Manual preview
RZN 4402-K V2
Бренд: D+H Страницы: 32
micro-trak MT-3405 LR F Reference Manual preview
MT-3405 LR F
Бренд: micro-trak Страницы: 44
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Бренд: Ros Страницы: 10
Variotech ENA3 Manual preview
ENA3
Бренд: Variotech Страницы: 24
JBSYSTEMS Light SCENE MASTER - V1.0 Operation Manual preview
SCENE MASTER - V1.0
Бренд: JBSYSTEMS Light Страницы: 24
CALEFFI AIR190002 Quick Start Manual preview
AIR190002
Бренд: CALEFFI Страницы: 14
G-Scale Graphics railboss 4 Operation And Installtion Manual preview
railboss 4
Бренд: G-Scale Graphics Страницы: 12
SEW MOVIFIT SC series Operating Instructions Manual preview
MOVIFIT SC series
Бренд: SEW Страницы: 148
Maintronic CBA UP Manual preview
CBA UP
Бренд: Maintronic Страницы: 53
YASKAWA E7N Technical Manual preview
E7N
Бренд: YASKAWA Страницы: 282
Madas RG/2MBLZ DN 80 Technical Manual preview
RG/2MBLZ DN 80
Бренд: Madas Страницы: 48
Wahlberg 255.700 User Manual preview
255.700
Бренд: Wahlberg Страницы: 40
Rexroth Indramat Mannesmann DKC21.3 Application preview
Mannesmann DKC21.3
Бренд: Rexroth Indramat Страницы: 38
Salus EP210 Installation Manual preview
EP210
Бренд: Salus Страницы: 24
Naturela NPBC-V3M-1 Manual preview
NPBC-V3M-1
Бренд: Naturela Страницы: 28
Cardin PRG384 Manual preview
PRG384
Бренд: Cardin Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды