manualshive.com logo in svg

Texas Instruments Concerto F28M35 Series, Техническое справочное руководство


Поделиться
Скачать
background image

www.ti.com

McBSP Registers

1123

SPRUH22I – April 2012 – Revised November 2019

Submit Documentation Feedback

Copyright © 2012–2019, Texas Instruments Incorporated

C28 Multichannel Buffered Serial Port (McBSP)

Table 15-72. Serial Port Control 1 Register (SPCR1) Field Descriptions (continued)

Bit

Field

Value

Description

1

RRDY

Receiver ready bit. RRDY is set when data is ready to be read from DRR[1,2]. Specifically, RRDY
is set in response to a copy from RBR1 to DRR1.

If the receive interrupt mode is RINTM = 00b, the McBSP sends a receive interrupt request to the
CPU when RRDY changes from 0 to 1.

Also, when RRDY changes from 0 to 1, the McBSP sends a receive synchronization event (REVT)
signal to the DMA controller.

0

Receiver not ready

When the content of DRR1 is read, RRDY is automatically cleared.

1

Receiver ready: New data can be read from DRR[1,2].

Important: If both DRRs are required (word length larger than 16 bits), the CPU or the DMA
controller must read from DRR2 first and then from DRR1. As soon as DRR1 is read, the next
RBR-to-DRR copy is initiated. If DRR2 is not read first, the data in DRR2 is lost.

0

RRST

Receiver reset bit. You can use RRST to take the McBSP receiver into and out of its reset state.
This bit has a negative polarity; RRST = 0 indicates the reset state.

To read about the effects of a receiver reset, see

Section 15.10.2

,

Resetting and Initializing a

McBSP

.

0

If you read a 0, the receiver is in its reset state.

If you write a 0, you reset the receiver.

1

If you read a 1, the receiver is enabled.

If you write a 1, you enable the receiver by taking it out of its reset state.

Содержание Concerto F28M35 Series
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Concerto F28M35 Series

Particle B Series Quick Start Manual preview
B Series
Бренд: Particle Страницы: 6
Badger Meter PC100 Installation And Operation Manual preview
PC100
Бренд: Badger Meter Страницы: 20
FAAC E124 Original Instructions Manual preview
E124
Бренд: FAAC Страницы: 44
Fagor CNC 8070 Programming Manual preview
CNC 8070
Бренд: Fagor Страницы: 556
UCS CAT Quick Start Manual preview
CAT
Бренд: UCS Страницы: 4
iluminize 5110 V1 Manual preview
5110 V1
Бренд: iluminize Страницы: 2
Bettis TEC2 Quick Start Manual preview
TEC2
Бренд: Bettis Страницы: 18
Murphy MURPHYMATIC ASM160 Installation And Operation Instructions preview
MURPHYMATIC ASM160
Бренд: Murphy Страницы: 4
Mold-Masters TempMaster M2 Plus Series Quick Manual preview
TempMaster M2 Plus Series
Бренд: Mold-Masters Страницы: 2
Trinamic TMCM-1240 Hardware Manual preview
TMCM-1240
Бренд: Trinamic Страницы: 30
Festo CPX-CEC Electronic Manual preview
CPX-CEC
Бренд: Festo Страницы: 87
Aqua Lung Cousteau/ SEA Service & Repair Manual preview
Cousteau/ SEA
Бренд: Aqua Lung Страницы: 24
Swagelok TBVS4 User Manual preview
TBVS4
Бренд: Swagelok Страницы: 16
Eaton Jockey XTJP O & M Manual preview
Jockey XTJP
Бренд: Eaton Страницы: 12
AMALGAMATED INSTRUMENT PM4-RT8 Operation And Instruction Manual preview
PM4-RT8
Бренд: AMALGAMATED INSTRUMENT Страницы: 27
Unika AR3600I User Instructions preview
AR3600I
Бренд: Unika Страницы: 14
Hanbay RD-AC Series User Manual preview
RD-AC Series
Бренд: Hanbay Страницы: 13
Gigarise SetPro MV Series Instruction Manual preview
SetPro MV Series
Бренд: Gigarise Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды