6 – Modules
4
icon
Tap this icon to open the TALKBACK/OSCILLATOR page of the
MONITOR SETUP Screen. (See “Making talkback and built-in
oscillator settings” on page 52.)
5
OSC button
When the LOCK/UNLOCK button (
3
) is set to “UNLOCK”, tap
this button to turn internal oscillator input on or off (default).
When on, the signal from the internal oscillator will be input
to the selected module while maintaining the input source
setting for that module. (Default: OFF)
When on, this button will appear highlighted and the INPUT
SOURCE selection (
2
) button area will be dimmed.
6
POST D. TRIM level meter(s)
This shows the signal level(s) after the D. TRIM.
7
Analog GAIN knob and indicator
o
When the input source of the selected module is
“ANALOG” or “SB-16D connected by built-in Dante”, this
will show an analog gain knob that can be used to adjust
the input level of the MIC/LINE input jacks on this unit or
the SB-16D.
Turn LCD knob 1 (lit red) to adjust it.
When Analog Reference Level = +6 dBu
PAD button setting
Range
OFF
+3 (default) – +57
ON
−17 – +37
When Analog Reference Level = +4 dBu
PAD button setting
Range
OFF
+12 (default) – +66
ON
−8 – +46
When Analog Reference Level = 0 dBu
PAD button setting
Range
OFF
+8 (default) – +62
ON
−12 – +42
o
This indicator appears to light with the color shown below
depending on the input level.
Red: −3 dBFS, Green: −40 dBFS
o
When the input source of the selected module is an
“ANALOG” stereo module, 2 Analog GAIN knobs will be
shown.
Use LCD knobs 1–2 (lit red) to adjust them.
NOTE
Explanation of Analog GAIN values
When signals at the Analog Reference Level (+6 dBu, +4 dBu,
0 dBu) are input, the Analog GAIN value that becomes the
Digital Reference Level (−9 dBFS, −14 dBFS, −16 dBFS, −18
dBFS, −20 dBFS) at the digital stage is shown as “0”.
8
PAD button
o
This shows the PAD button when the input source of the
selected module is “ANALOG” or “SB-16D connected by
built-in Dante”.
o
Tap this button to turn the –20dB pad on/off. (Default: off)
When this button is on, it will appear highlighted.
NOTE
When the pad is switched on/off, the Analog GAIN value will
be controlled as shown below so that it changes as little as
possible.
When Analog Reference Level = +6 dBu
Status before switching pad
setting
Analog GAIN after
switching pad setting
Analog GAIN: +3 – +37
Same value
PAD ON/Analog GAIN: −17 – +2
+3
PAD OFF/Analog GAIN: +38 – +57 +37
When Analog Reference Level = +4 dBu
Status before switching pad
setting
Analog GAIN after
switching pad setting
Analog GAIN: +12 – +46
Same value
PAD ON/Analog GAIN: −8 – +11
+12
PAD OFF/Analog GAIN: +47 – +66 +46
When Analog Reference Level = 0 dBu
Status before switching pad
setting
Analog GAIN after
switching pad setting
Analog GAIN: +8 – +42
Same value
PAD ON/Analog GAIN: −12 – +7
+8
PAD OFF/Analog GAIN: +43 – +62 +42
9
GANG button
o
This shows the GANG button when the input source of the
selected module is an “ANALOG” or “SB-16D connected by
built-in Dante” stereo module.
o
Tap this button to turn the GANG function on/off. Turning
the GANG function on, highlighting the button, will
enable the simultaneous linked operation of the 2 Analog
GAIN knobs. (Default: OFF)
0
8ch BLOCK button (CH 1–40 modules only)
When the LOCK/UNLOCK button (
3
) is set to “UNLOCK”, tap
this button to open a window where the input sources of
8 channels can be set at the same time. (See “Setting input
sources for multiple channels at the same time in blocks” on
page 65.)
Change settings for multiple designated channels at the
same time.
NOTE
i
This cannot be used when the LOCK/UNLOCK button (
3
) is
set to “LOCK”.
i
If routing operation is set to “LOCK” on another touchscreen
while a multiple setting window is open, it will close
automatically.
88
TASCAM Sonicview 16/Sonicview 24
