Tascam Sonicview 16 Скачать руководство пользователя страница 105

Страница: 105 / 188

6 – Modules

IMAGE

Use this to adjust the image width of the stereo signal.
The farthest left produces ordinary stereo. Turning it right

reduces the stereo width until the center where it becomes

mono. Turning it further to the right reverses the stereo

positions until left and right are completely reversed at the

farthest right.

Range: STEREO 100% – MONO – REVERSE 100%

(default: STEREO 100%)

When the selection frame is shown, turn LCD knob 7 (lit green)

to adjust it.

NOTE

This is only shown when the selected module is a CH 1–40

module with the Stereo Link setting on, or a ST IN 1–2 or FX

RTN 1–4 module.

BAL indicator (shown for stereo modules only)

This adjusts the balance of the signals sent to the MAIN L/R

bus.

Range: L100 – C – R100 (default: C)

When the selection frame is shown, turn LCD knob 8 (lit yellow)

to adjust it.

NOTE

A list of PAN/BAL settings can be viewed and operated for the

MAIN L/R bus on the SEND PAN (INPUT) and SEND PAN (BUS)

Screen (“MAIN L/R bus SEND OVERVIEW Screen” on page

116).

This is not shown when the selected module is the MAIN L/R

Master module.

When BAL settings are centered (C), the left channel is sent

to the MAIN L bus and the right channel is sent to the MAIN R

bus at 0 dB.

Tap this area while pressing the HOME key on the top panel

to set the balance to center (C).

TASCAM Sonicview 16/Sonicview 24

105

Содержание Sonicview 16





























































































































































































Результаты поиска

Содержание Sonicview 16

Отзывы:

Похожие инструкции для Sonicview 16

Бренды по названию

Популярные бренды

Tascam Sonicview 16, Справочное руководство

Результаты поиска

Содержание Sonicview 16

Отзывы:

Похожие инструкции для Sonicview 16

Бренды по названию

Популярные бренды