Tascam Sonicview 16 Скачать руководство пользователя страница 44

Страница: 44 / 188

4 – Mixer configuration and settings

Foot Switch page

Functions can be assigned to the footswitch on this page.
Tap Menu Screen > Rear Panel Setup > FOOT SW Setup to open

this page.

Foot Switch page when setting controls

The factory default setting is “Tap Tempo FX3 Delay1”.

Setting the footswitch polarity

This unit was designed to be used with momentary footswitches

that must be pushed to function (shorted when pushed). Since

the polarity can be reversed, however, push-to-break (shorted

with not pushed) footswitches can also be used.
The setting of this unit can be changed according to the polarity

of the footswitch being used.
1. Tap the

button on the USER DEFINED CONTROLS Screen

to open a settings window.

2. Tap the Foot Switch Polarity slider in the window to set the

footswitch polarity.

Options: Normal (default), Invert

GPIO-IN page

On this page, functions can be assigned to the GPIO input

connector of this unit or of an SB-16D connected through the

built-in Dante.
Tap Menu Screen > Rear Panel Setup > GPIO Input Setup to

open this page.

GPIO-IN page when setting controls

The factory default settings are as follows.

Port number

Assigned function

Mute Group 1

Mute Group 2

Mute Group 3

Mute Group 4

Mute Group 5

Talkback ON/OFF

Tap Tempo FX3 Delay1

Tap Tempo FX4 Delay1

TASCAM Sonicview 16/Sonicview 24

Содержание Sonicview 16





























































































































































































Результаты поиска

Содержание Sonicview 16

Отзывы:

Похожие инструкции для Sonicview 16

Бренды по названию

Популярные бренды

Tascam Sonicview 16, Справочное руководство

Результаты поиска

Содержание Sonicview 16

Отзывы:

Похожие инструкции для Sonicview 16

Бренды по названию

Популярные бренды