Tascam Sonicview 16, Справочное руководство

Страница: 103 / 188

6 – Modules
1
SEND levels, SEND PAN and ON/OFF buttons for
MIX 1–22 buses
This shows the SEND settings for MIX 1–22 buses.
a
This shows the user module names for the MIX 1–22
modules. If the name has not been defined, the MIX
module number, for example “1”, will be shown.
b
This shows the send position settings for the MIX 1–22
buses.
No indicator Set to POST FADER
PRE
Set to PRE FADER
c
Use this to adjust the send levels to the MIX 1–22
buses. When a selection frame is shown, use
corresponding LCD knobs (lit orange) to adjust values.
Assignment on Shown in orange
Assignment off Shown in gray
Range: - ∞ dB - +10 dB (default: - ∞ dB)
d
Tap this button to turn on/off signals sent to the MIX
1–22 buses.
Module default
CH 1-40/ST IN 1-2/FX RTN 1-4 ON
MIX 1–22/MAIN L/R Master OFF
e
This adjusts the SEND PAN of the signal sent to the
MIX 1–22 buses. When a selection frame is shown, use
corresponding LCD knobs (lit yellow) to adjust values.
Range: L100 – C – R100 (default: C)
f
Rounded buttons are shown for MIX 1–22 modules set
to GROUP buses. Tap this button to turn it on and off.
NOTE
i
A list of SEND settings for each bus can be viewed and
operated (“MIX 1–22 bus SEND OVERVIEW Screen” on page
111).
i
Tap the SEND level area while pressing the HOME key on the
top panel to set the SEND level for that bus to 0 dB.
i
Tap the SEND PAN area while pressing the HOME key on the
top panel to set the SEND PAN for the tapped bus to center
(C).
i
When Stereo Link is on for a MIX 1–22 bus, the PAN status
will be shown in the bus area of the lower number, and the
level and button will be shown in the bus area of the higher
number.
i
SEND PAN parameters for buses with the PAN LINK setting
on appear dim. Tapping them will not select them and they
cannot be operated. They are linked to the PAN/BAL setting.
i
When a MIX 1–22 module is selected, the SEND level and
button to the same bus as the selected module are not
shown.
i
If a MIX 1–22 bus is already assigned to the MAIN L/R bus,
trying to turn this MIX button on for the MAIN L/R Master
module will produce an error message. To prevent a feedback
loop, it cannot be turned on.
2
SEND levels and ON/OFF buttons for FX 1–4 buses
This shows the SEND settings for FX 1–4 buses.
a
This shows the user module names for the FX RTN
1–4 modules. If the name has not been defined, the
module name will be shown as “FX 1”, for example.
b
This shows the send position setting for the FX 1–4 bus.
No indicator Set to POST FADER
PRE Set to PRE FADER
c
Use this to adjust the send level to the FX 1–4 bus.
When a selection frame is shown, use corresponding
LCD knobs (lit green) to adjust values.
Assignment on Shown in green
Assignment off Shown in gray
Range: - ∞ dB - +10 dB (default: - ∞ dB)
d
Tap this button to turn on/off the signal sent to the FX
1–4 bus.
Options: ON (default), OFF
NOTE
i
This is not shown when the selected module is an FX RTN 1–4
or MAIN L/R Master module.
i
A list of SEND settings for each bus can be viewed and
operated (“FX 1–4 bus SEND OVERVIEW Screen” on page
114).
i
Tap the SEND level area while pressing the HOME key on the
top panel to set the SEND level for that bus to 0 dB.
TASCAM Sonicview 16/Sonicview 24
103