Tascam Sonicview 16 Скачать руководство пользователя страница 52

Страница: 52 / 188

4 – Mixer configuration and settings

Making talkback and built-in

oscillator settings

Make settings for talkback and the built-in oscillator on the

MONITOR SETUP screen TALKBACK/OSCILLATOR page.
Tap Menu Screen > Mixer Setup > Talkback/OSC Setup to open

this screen.

NOTE

This screen can also be opened by pressing the TALKBACK

key while pressing the MENU key. (See “12 – List of shortcut

operations” on page 168.)

Using the User Defined Control function, this screen can also

be opened with a USER KEY, footswitch or the GPIO-IN. (See

“USER DEFINED CONTROLS screen” on page 38.)

Each level meter has an overload indicator at its top.

TALKBACK ASSIGN

Tap these buttons to set the outputs for the talkback signal.

(These are off by default.)
Buttons for selected outputs will be highlighted.

NOTE

Stereo buses have a single button for each pair.

OSCILLATOR ASSIGN

Tap these buttons to set the outputs for the built-in oscillator

signal. (These are off by default.)
Buttons for selected outputs will be highlighted.

NOTE

Outputs can be turned on/off independently even for stereo

buses.

TALKBACK button

Tap this button to turn the TALKBACK function ON and OFF

(default).
When this is ON, the button will appear highlighted.

NOTE

This has the same function as the TALKBACK key on the top

panel.

Tap this button to switch it ON and OFF. Touch this button

continuously to turn the function on only while being

touched.

Using the User Defined Control function, TALKBACK ON/OFF

switching is also possible with a USER KEY, the footswitch or the

GPIO-IN. (See “USER DEFINED CONTROLS screen” on page

38.)
This function is assigned to the following GPIO-IN on the

GPIO-IN page by default.

GPIO-IN 6 (Talkback ON/OFF)

TALKBACK level meter

This shows the TALKBACK signal input level.

D.TRIM knob

Use this to adjust the TALKBACK signal digital trim value.

Range: -20 dB - +20 dB (default: 0 dB)

Turn LCD knob 2 (lit red) to adjust it.

NOTE

Use the TALKBACK volume knob on the top panel to adjust

the TALKBACK input level. (See “

TALKBACK volume” on

page 9.)

TB DIM knob

When talkback is on, this adjusts the amount that the bus

being used is attenuated.

Range: -40 dB - 0 dB (default: -20 dB)

Turn LCD knob 3 (lit red) to adjust it.

+48V button

Use this button to 48V phantom power to the

TALKBACK jack on the rear panel.
Touch and hold the +48V button to turn phantom power

(+48V) ON and OFF (default).
When this is ON, the button will appear highlighted.

OSCILLATOR button

Tap this button to turn the built-in oscillator signal ON and

OFF (default).
When this is ON, the button will appear highlighted.

OSCILLATOR level meter

This shows the output level of the built-in oscillator.

OSC LEVEL knob

Use this to adjust the output level of the built-in oscillator.

Range: -36 dB - 0 dB (default: -20 dB)

Turn LCD knob 6 (lit red) to adjust it.

TASCAM Sonicview 16/Sonicview 24

Содержание Sonicview 16





























































































































































































Результаты поиска

Содержание Sonicview 16

Отзывы:

Похожие инструкции для Sonicview 16

Бренды по названию

Популярные бренды

Tascam Sonicview 16, Справочное руководство

Результаты поиска

Содержание Sonicview 16

Отзывы:

Похожие инструкции для Sonicview 16

Бренды по названию

Популярные бренды