Isuzu 2008MY N Series Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 404

background image

Engine Control System (4HK1) 1A-139

Circuit/ System Testing DTC P0204

15

Important:

Replacement fuel injector must be

programmed.
Replace the cylinder #3 fuel injector. Refer to
Injector in Section 1D Engine Fuel.

Did you complete the replacement?

—

Go to Step 17

—

16

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 17

—

17

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 18

18

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check
- Engine Controls?

—

Go to Step 2

Go to Diagnostic

System Check -
Engine Controls

2

1.

Install a scan tool.

2.

Turn OFF the ignition for 30 seconds.

3.

Start the engine.

4.

Monitor the DTC Information with a scan tool.

Does the DTC fail this ignition?

—

Go to Step 3

Go to Diagnostic

Aids

3

1.

Turn OFF the ignition.

2.

Disconnect the in-line harness connector from
the cylinder head cover case.

3.

Measure the resistance of the charge voltage
circuit across the female side connector.

4.

Measure the resistance of the charge voltage
circuit across the male side connector.

Are both resistance readings less than the
specified value (either of reading is out of
specified value will not set this DTC)?

1.0

Ω

Go to Step 4

Go to Step 9

LG4HKED-WE-0871.book 139

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
140
141
142
143
144
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Haier Страницы: 58

Бренд: Vacon Страницы: 64

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: Bartlett Страницы: 5

Бренд: Ravaglioli Страницы: 90

Бренд: Raypak Страницы: 24

Бренд: rauland Страницы: 2

Бренд: J+J Страницы: 91

Бренд: IMG STAGELINE Страницы: 14

Бренд: VAT Страницы: 77

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды