Isuzu 2008MY N Series Скачать руководство пользователя страница 284

Страница: 284 / 404

Engine Control System (4HK1) 1A-281

Important:

The BARO sensor may be damaged if

the sensor signal circuit is shorted to a voltage
source.
1.

Test the signal circuit between the ECM (pin
71 of J-14) and the BARO sensor (pin 1 of B-
121) for the following conditions:

• A short to battery or ignition voltage
• A short to any 5 volts reference

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 13

Go to Step 12

Notice:

The BARO sensor shares the low

reference circuit with other sensors. A fault
condition in the low reference circuit may set DTCs
on sensors that share this circuit.
1.

Test the low reference circuit between the
ECM (pin 60 of J-14 and the BARO sensor
(pin 1 of B-121) for an open circuit or high
resistance.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 13

Go to Step 10

Inspect for an intermittent and for a poor
connection at the harness connector of the
BARO sensor (pin 1 of B-121).

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 13

Go to Step 11

Turn OFF the ignition.

Disconnect the ECM harness connector.

Inspect for an intermittent and for a poor
connection at the harness connector of the
ECM (pin 60 of J-14).

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 13

Go to Step 12

Replace the BARO sensor. Refer to BARO Sensor
Replacement.

Did you complete the replacement?

—

Go to Step 13

—

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 13

—

Reconnect all previously disconnected
harness connector(s).

Clear the DTCs with a scan tool.

Turn OFF the ignition for 30 seconds.

Start the engine.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 2

Go to Step 14

Step

Action

Value(s)

Yes

LG4HKED-WE-0871.book 281

ページ

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды

Isuzu 2008MY N Series, Руководство по ремонту

Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды