Isuzu 2008MY N Series Скачать руководство пользователя страница 148

Страница: 148 / 404

Engine Control System (4HK1) 1A-145

Inspect the CKP sensor and sensor rotor for
the following conditions:

• Physical damage of sensor
• Loose or improper installation of sensor
• Excessive air gap
• Foreign material passing between sensor

and sensor rotor

• Physical damage of sensor rotor
• Loose or improper installation of sensor

rotor

Repair or replace as necessary.

Did you find and correct the condition?

—

Go to Step 6

Go to Step 5

Replace the CKP sensor. Refer to CKP Sensor in
Section 1B Engine Mechanical.

Did you complete the replacement?

—

Go to Step 5

—

Reconnect all previously disconnected
harness connector(s).

Clear the DTCs with a scan tool.

Turn OFF the ignition for 30 seconds.

Start the engine.

Accelerate the engine between idle and
W.O.T. (accelerator pedal full travel) many
times while observing the Engine Speed
parameter with a scan tool.

Does the Engine Speed parameter ever
exceed the specified value?

3700 RPM

Go to Step 4

Go to Step 7

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

LG4HKED-WE-0871.book 145

ページ

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды

Isuzu 2008MY N Series, Руководство по ремонту

Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды