Isuzu 2008MY N Series Скачать руководство пользователя страница 201

Страница: 201 / 404

1A-198 Engine Control System (4HK1)

Circuit/ System Testing DTC P0500 (Model with ABS)

Inspect the VSS, drive gear, driven gear or
output shaft for the following conditions:

• Physical damage of sensor, drive gear or

driven gear

• Loose or improper installation of sensor,

drive gear or driven gear

• Transmission output shaft teeth damage
• Excessive transmission output shaft play

Repair or replace as necessary.

Did you find and correct the condition?

—

Go to Step 7

Go to Step 5

Turn OFF the ignition.

Inspect for an intermittent, for poor
connections and corrosion at the harness
connector of the VSS (pins 1, 2 and 3 of J-48).

Disconnect the ECM harness connector.

Inspect for an intermittent, for a poor
connection and corrosion at the harness
connector of the ECM (pin 19 of J-14).

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 7

Go to Step 6

Replace the VSS. Refer to Vehicle Speed Sensor in
Section 9E Instrumentation/Driver Info.

Did you complete the replacement?

—

Go to Step 7

—

Reconnect all previously disconnected
harness connector(s).

Clear the DTCs with a scan tool.

Turn OFF the ignition for 30 seconds.

Drive the vehicle while observing the Vehicle
Speed parameter with a scan tool.

Does the scan tool indicate correct vehicle
speed?

—

Go to Step 8

Go to Step 2

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

Did you perform the Diagnostic System Check
- Engine Controls?

—

Go to Step 2

Go to Diagnostic

System Check -

Engine Controls

Install a scan tool.

Turn OFF the ignition for 30 seconds.

Start the engine.

Monitor the DTC Information with a scan tool.

Is DTC P0502 or P0503 also set?

—

Go to Applicable

DTC

Go to Step 3

Observe the ABS DTCs information with a scan
tool.

Is DTC C0251, C0252, C0253, C0254,
C0261, C0262, C0263 or C0264 set?

—

Go to Applicable

DTC

Go to Step 4

Step

Action

Value(s)

Yes

LG4HKED-WE-0871.book 198

ページ

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды

Isuzu 2008MY N Series, Руководство по ремонту

Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды