Isuzu 2008MY N Series Скачать руководство пользователя страница 341

Страница: 341 / 404

1A-338 Engine Control System (4HK1)

Inspect the following conditions:

• Misrouted or disconnected exhaust

differential pressure hoses or pipes

Important:

There is installation

directionality in the exhaust differential
pressure hoses. Refer to Exhaust
System in Section 1G Engine Exhaust .

• Plugged, crushed or kinked exhaust

differential pressure hoses or pipes

• Dislocated or inclined exhaust differential

pressure sensor. Refer to Exhaust
System in Section 1G Engine Exhaust .

• Physical damage of the exhaust

differential pressure sensor

• Any contamination or objects that block

the exhaust differential pressure sensor
port

• Skewed or slow exhaust differential

pressure sensor

• An exhaust system gasket that is missing

or damaged

• Exhaust gas leakage from the exhaust

pipe, gasket, DPD assembly, exhaust
temperature sensor(s) or exhaust
differential pressure hoses or pipes

• Modified exhaust system
• Exhaust throttle valve or exhaust brake

valve for stuck condition. Refer to
Exhaust System in Section 1G Engine
Exhaust.

• Skewed or slow exhaust temperature

sensors

• Restricted air cleaner element, restricted

or collapsed air tubing between the air
cleaner and the intake manifold

• Modified air induction
• Any air induction leak
• Any contamination or objects that block

the mass air flow (MAF) sensor inlet

• Skewed or slow MAF sensor

Repair or replace as necessary.

Did you find and correct the condition?

—

Go to Step 14

Go to Step 5

Start the engine and let idle for 30 seconds.

Does the DPD lamp or “PUSH DPD SWITCH”
indicator blink?

—

Go to Step 6

Go to Step 7

Perform the DPD manual regeneration by pressing
the DPD switch.

Does the regeneration start?

—

Go to Step 10

ECM is not allowing

the DPD

regeneration

control. Refer to

Test Description and

DTC List

Observe the DPD Accumulation Status and DPD
Distance Status with a scan tool, and plot both
readings on the DPD status table.

Is the intersected range located in A or B?

—

Go to Step 8

Go to Step 9

Step

Action

Value(s)

Yes

LG4HKED-WE-0871.book 338

ページ

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды

Isuzu 2008MY N Series, Руководство по ремонту

Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды