Isuzu 2008MY N Series Скачать руководство пользователя страница 193 | Manualshive

Страница: 193 / 404

background image

1A-190 Engine Control System (4HK1)

Circuit/ System Testing DTC P042D

4

1.

Turn OFF the ignition.

2.

Disconnect the exhaust temperature sensor 2
harness connector.

3.

Turn ON the ignition, with the engine OFF.

Is the Exhaust Temperature Sensor 2
parameter more than the specified value?

4.5 volts

Go to Step 6

Go to Step 5

5

1.

Test the signal circuit between the ECM (pin
74 of J-14) and the exhaust temperature
sensor 2 (pin 2 of J-35) for the following
conditions:

• A short to ground
• A short to the low reference circuit

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 9

Go to Step 7

6

Replace the exhaust temperature sensor 2. Refer
to Exhaust Temperature Sensor in Section 1G
Engine Exhaust.

Did you complete the replacement?

—

Go to Step 9

—

7

1.

Turn OFF the ignition.

2.

Disconnect the ECM harness connector.

3.

Inspect connections at the harness connector
of the ECM (pins 74 and 79 of J-14) for
corrosion.

4.

Repair or clean the connection(s) as
necessary.

Did you find and correct the condition?

—

Go to Step 9

Go to Step 8

8

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 9

—

9

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Failure Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 10

10

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check
- Engine Controls?

—

Go to Step 2

Go to Diagnostic

System Check -

Engine Controls

LG4HKED-WE-0871.book 190

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
191
192
193
194
195
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: rada Страницы: 16

Бренд: VCON Страницы: 66

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: Gascat Страницы: 32

Бренд: Garz & Fricke Страницы: 35

Бренд: Harsco Industrial Страницы: 57

Бренд: Harmar Mobility Страницы: 53

Бренд: Walimex Pro Страницы: 68

Бренд: Lawler Страницы: 5

Бренд: Waterway Страницы: 8

Бренд: V2 Страницы: 12

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

TVNext NN01-054

Бренд: Fractus Antennas Страницы: 14

Бренд: Kampmann Страницы: 5

Waukesha Cherry-Burrell D4 Series

Бренд: SPX FLOW Страницы: 34

Бренд: Contemporary Research Страницы: 22

Бренд: Jeckson Electric Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды