Isuzu 2008MY N Series Скачать руководство пользователя страница 212 | Manualshive

Страница: 212 / 404

background image

Engine Control System (4HK1) 1A-209

14

1.

Turn OFF the ignition.

2.

Disconnect the ECM harness connector.

3.

Inspect for an intermittent and for a poor
connection at the harness connector of the
ECM (pin 35 of J-14).

4.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 18

Go to Step 17

15

Replace the dropping resistor.

Did you complete the replacement?

—

Go to Step 18

—

16

Replace the MAF sensor. Refer to MAF/IAT Sensor
in Section 1J Induction.

Did you complete the replacement?

—

Go to Step 18

—

17

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 18

—

18

1.

Reconnect all previously disconnected fuse or
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Turn ON the ignition, with the engine OFF.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 19

19

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 209

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
210
211
212
213
214
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Keithley Страницы: 97

Бренд: Happ Страницы: 52

Бренд: Hansen Страницы: 4

Бренд: B&R Industries Страницы: 89

Бренд: Ebyte Страницы: 35

Бренд: H3C Страницы: 5

Бренд: H3C Страницы: 4

Бренд: V2 ELETTRONICA Страницы: 72

Бренд: Parkside Страницы: 65

Бренд: Delabie Страницы: 20

Бренд: Linear Technology Страницы: 32

Бренд: National Instruments Страницы: 26

Бренд: Hall Technologies Страницы: 10

Бренд: National Instruments Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды