Isuzu 2008MY N Series Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 404

background image

1A-178 Engine Control System (4HK1)

10

1.

Test the position sensor circuits (which ever
parameter did not indicate High at Step 6)
between the ECM (pins 93, 94 and 99 of E-12)
and the EGR valve (pins 2, 3 and 4 of E-15)
for the following conditions:

• An open circuit
• A short to ground
• A short to the low reference circuit
• High resistance

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 16

Go to Step 13

11

1.

Inspect for an intermittent and for poor
connections at the harness connector of the
EGR valve (pins 1, 2, 3, 4 and 5 of E-15)

2.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 16

Go to Step 12

12

1.

Test the solenoid circuits between the ECM
(pins 103, 110 and 111 of E-12) and the EGR
valve (pins 6, 7 and 8 of E-15) for a short to
the EGR position sensor circuit(s).

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 16

Go to Step 14

13

1.

Turn OFF the ignition.

2.

Disconnect the ECM harness connector.

3.

Inspect for an intermittent and for poor
connections at the harness connector of the
ECM (pins 87, 93, 94, 99 and 101 of E-12).

4.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 16

Go to Step 15

14

Replace the EGR valve. Refer to EGR Valve and
EGR Cooler in Section 1F Emission Control.

Did you complete the replacement?

—

Go to Step 16

15

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 16

16

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

Notice:

A history DTC will not clear. (Euro 4

specification)

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 17

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 178

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
179
180
181
182
183
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: Vacon Страницы: 64

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: National Instruments Страницы: 29

Бренд: R. Beck Maschinenbau Страницы: 35

Бренд: Velleman Страницы: 26

Бренд: Velleman Страницы: 32

Бренд: Velocity Страницы: 84

Бренд: Watlow Страницы: 4

Бренд: NAiS Страницы: 144

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

Бренд: DAY Страницы: 23

Lift Inverter L1000V

Бренд: YASKAWA Страницы: 282

Бренд: NDS Страницы: 20

Бренд: National Instruments Страницы: 18

Бренд: HEEVE Страницы: 8

Бренд: Rauch Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды