Isuzu 2008MY N Series Скачать руководство пользователя страница 171

Страница: 171 / 404

1A-168 Engine Control System (4HK1)

Turn OFF the ignition.

Disconnect the ECM J-14 harness connector.

Turn ON the ignition, with the engine OFF.

Is the MIL OFF?

—

Go to Step 6

Go to Step 12

Remove the Meter (10A) fuse that supplies
voltage to the MIL.

Turn ON the ignition, with the engine OFF.

Measure the voltage from the glow indicator
lamp control circuit in the ECM harness
connector (pin 11 of J-14) to a known good
ground.

Is the voltage less than the specified value?

1 volt

Go to Step 7

Go to Step 13

Turn OFF the ignition.

Reinstall the Meter (10A) fuse.

Turn ON the ignition, with the engine OFF.

Connect a 3-amp fused jumper wire between
the ECM harness connector (pin 11 of J-14)
and a known good ground.

Is the MIL illuminated?

—

Go to Step 11

Go to Step 8

Connect a test lamp between the ignition
voltage feed circuit of the IP cluster harness
connector (pin 2 of B-105) and a known good
ground.

Turn ON the ignition, with the engine OFF.

Does the test lamp illuminate?

—

Go to Step 9

Go to Step 14

Test the control circuit between the ECM (pin
11 of J-14) and the IP cluster (pin 5 of B-106)
for an open circuit or high resistance.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 10

Inspect for an intermittent and for poor
connections at the harness connector of the
IP cluster (pins 2 and 5 of B-105).

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 15

Inspect for an intermittent and for a poor
connection at the harness connector of the
ECM (pin 11 of J-14).

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 16

Repair the short to ground between the ECM (pin
11 of J-14) and the IP cluster (pin 5 of B-106).

Did you complete the repair?

—

Go to Step 17

—

Repair the short to battery or ignition voltage
between the ECM (pin 11 of J-14) and the IP
cluster (pin 5 of B-106).

Did you complete the repair?

—

Go to Step 17

—

Step

Action

Value(s)

Yes

LG4HKED-WE-0871.book 168

ページ

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды

Isuzu 2008MY N Series, Руководство по ремонту

Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды