Isuzu 2008MY N Series Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 404

background image

Engine Control System (4HK1) 1A-111

9

Notice:

The IAT sensor shares the low reference

circuit with other sensors. A fault condition in the
low reference circuit may set DTCs on sensors that
share this circuit.
1.

Test the low reference circuit between the
ECM (pin 60 of J-14) and the IAT sensor (pin 5
of J-38 [Euro 4 specification] or pin 2 of J-217
[Expect Euro 4 specification]) for an open
circuit or high resistance.

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 15

Go to Step 12

10

1.

Test the signal circuit between the ECM (pin
72 of J-14) and the IAT sensor (pin 4 of J-38
[Euro 4 specification] or pin 1 of J-217 [Expect
Euro 4 specification]) for a short to any 5 volts
reference circuit.

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 15

Go to Step 11

11

1.

Inspect for an intermittent and for poor
connections at the harness connector of the
IAT sensor (pins 4 and 5 of J-38 [Euro 4
specification] or pins 1 and 2 of J-217 [Expect
Euro 4 specification]).

2.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 15

Go to Step 13

12

1.

Turn OFF the ignition.

2.

Disconnect the ECM harness connector.

3.

Inspect for an intermittent and for poor
connections at the harness connector of the
ECM (pins 60 and 72 of J-14).

4.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 15

Go to Step 14

13

Replace the MAF sensor or the IAT sensor. Refer
to MAF/IAT Sensor in Section 1J Induction.

Did you complete the replacement?

—

Go to Step 15

—

14

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 15

—

15

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 16

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 111

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
112
113
114
115
116
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: Palfinger Страницы: 34

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Van Air Страницы: 4

Бренд: Quectel Страницы: 90

Бренд: Radionics Страницы: 14

Бренд: Centurion Страницы: 16

phyCORE-MCF548x

Бренд: Phytec Страницы: 104

IntelliCross TouchFree Kit

Бренд: Novax Страницы: 3

Бренд: Daikin Страницы: 19

Бренд: Wenglor Страницы: 44

Бренд: Controlsoft Страницы: 12

ACTIVAL VY51 5H006

Бренд: Azbil Страницы: 20

Бренд: Firmtech Страницы: 19

Бренд: FAIE Страницы: 5

Бренд: GEM Страницы: 31

Бренд: ICP DAS USA Страницы: 4

InRAX MVI46-PDPS

Бренд: ProSoft Technology Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды