Isuzu 2008MY N Series Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 404

background image

1A-80 Engine Control System (4HK1)

2

1.

Install a scan tool.

2.

Turn OFF the ignition for 30 seconds.

3.

Start the engine.

4.

Monitor the DTC Information with a scan tool.

Is DTC P0089, P0091, P0092, P0192, P0193,
P0201 - P0204, P2146 or P2149 set?

—

Go to Applicable

DTC

Go to Step 3

3

1.

Turn OFF the ignition.

2.

Place the transmission in Neutral and set the
parking brake.

3.

Start the engine.

4.

Accelerate the engine between idle and
W.O.T. (accelerator pedal full travel) many
times while observing the Fuel Rail Pressure
parameter with a scan tool.

Does the Fuel Rail Pressure parameter ever
exceed the specified value?

180 MPa

(26,000 psi)

Go to Step 4

An intermittent

problem by foreign

material in the fuel

system is

suspected. Go to

Step 13

4

1.

Turn OFF the ignition.

2.

Wait 1 minute for the fuel pressure to bleed
down from the fuel rail.

3.

Turn ON the ignition, with the engine OFF.

4.

Observe the Fuel Rail Pressure (FRP) Sensor
parameter with the scan tool.

Does the scan tool indicate within the
specified value?

0.9 to 1.0 volt

Go to Step 5

Go to Step 12

5

1.

Start the engine.

2.

Perform the Cylinder Balance Test with a scan
tool.

3.

Command each injector OFF and verify an
engine speed change for each injector.

Is there an injector that does not change
engine speed when commanded OFF?

—

Go to Step 15

Go to Step 6

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 80

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
81
82
83
84
85
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: 1Control Страницы: 8

Бренд: TA Hydronics Страницы: 14

Бренд: Eagle Equipment Страницы: 32

Бренд: HABONIM Страницы: 9

Бренд: Kamstrup Страницы: 36

Бренд: JFA Electronicos Страницы: 29

Бренд: Zmotion Страницы: 48

Бренд: M-system Страницы: 13

EtherCAT Compact67 Slim

Бренд: elco Страницы: 28

Бренд: Vent-Axia Страницы: 4

Бренд: Harman Страницы: 2

TRANSITIONS Angled Entry Mat

Бренд: EZ-ACCESS Страницы: 4

Бренд: Linear Technology Страницы: 6

Бренд: Nortek Страницы: 24

Бренд: Anritsu Страницы: 54

Бренд: Governors America Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды