Isuzu 2008MY N Series Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 404

background image

1A-66 Engine Control System (4HK1)

3

1.

Inspect the crankshaft position (CKP) sensor
and the camshaft position (CMP) sensor for
the following conditions:

• Physical damage of sensor
• Loose or improper installation of sensor
• Excessive air gap
• Foreign material passing between sensor

and sensor rotor or camshaft gear

• Physical damage of sensor rotor or

camshaft gear

• Loose or improper installation of sensor

rotor or camshaft gear

2.

Inspect the engine mechanical timing for an
incorrectly installed timing gear or camshaft.

Notice:

If the flywheel dowel pin is missing or

pushed in and the flywheel is incorrectly
installed, this DTC may set.

3.

Repair or replace as necessary.

Did you complete the repair?

—

Go to Step 4

—

4

1.

Reconnect all previously disconnected
harness connector(s) if disconnected.

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine. If the engine does not start,
crank over the engine for 10 seconds.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 2

Go to Step 5

5

Observe the DTC Information with the a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 66

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
67
68
69
70
71
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: FAAC Страницы: 12

Бренд: ABB Страницы: 63

Бренд: Safeline Страницы: 8

Бренд: C.Nord Страницы: 100

CoreBuilder 9000

Бренд: 3Com Страницы: 78

REMOTE ACCESS SYSTEM 1500

Бренд: 3Com Страницы: 62

Бренд: UNITED Страницы: 22

Бренд: D+H Страницы: 14

Бренд: Dahua Страницы: 58

Бренд: H-P Products Страницы: 12

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Paradox Страницы: 32

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды