Isuzu 2008MY N Series Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 404

background image

Engine Control System (4HK1) 1A-109

Circuit/ System Testing DTC P0113

5

1.

Test the signal circuit between the ECM (pin
72 of J-14) and the IAT sensor (pin 4 of J-38
[Euro 4 specification] or pin 1 of J-217 [Expect
Euro 4 specification]) for the following
conditions:

• A short to ground
• A short to the low reference circuit

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 9

Go to Step 7

6

Replace the MAF sensor or the IAT sensor. Refer
to MAF/IAT Sensor in Section 1J Induction.

Did you complete the replacement?

—

Go to Step 9

—

7

1.

Turn OFF the ignition.

2.

Disconnect the ECM harness connector.

3.

Inspect connections at the harness connector
of the ECM (pins 60 and 72 of J-14) for
corrosion.

4.

Repair or clean the connection(s) as
necessary.

Did you find and correct the condition?

—

Go to Step 9

Go to Step 8

8

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 9

—

9

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 10

10

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check
- Engine Controls?

—

Go to Step 2

Go to Diagnostic

System Check -
Engine Controls

2

1.

Install a scan tool.

2.

Turn OFF the ignition for 30 seconds.

3.

Start the engine.

4.

Monitor the DTC Information with a scan tool.

Is DTC P0651 also set?

—

Go to DTC P0651

Go to Step 3

LG4HKED-WE-0871.book 109

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
110
111
112
113
114
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Evolution Series E9000

Бренд: GE Страницы: 44

PACSystems RX7i

Бренд: GE Страницы: 469

GuardSwitch 300 Series

Бренд: GE Страницы: 2

GuardSwitch 300 Series

Бренд: GE Страницы: 2

Masoneilan VariPak 28001

Бренд: GE Страницы: 24

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: UNITED Страницы: 8

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: Febco Страницы: 12

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Hanna Instruments Страницы: 88

Бренд: Yealink Страницы: 6

MeetingSpace VC800

Бренд: Yealink Страницы: 6

Бренд: Yealink Страницы: 16

Бренд: Yealink Страницы: 299

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды