Isuzu 2008MY N Series Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 404

background image

Engine Control System (4HK1) 1A-129

6

1.

Test the signal circuits between the ECM (pins
82 and 90 of E-12) and the FRP sensor (pin 2
of E-19) for the following conditions:

• A short to ground
• A short to the low reference circuit

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 12

Go to Step 11

7

Notice:

The FRP sensor shares the 5 volts

reference circuit with other sensors. A fault
condition in the 5 volts reference circuit may set
DTCs on sensors that share this circuit.
1.

Test the 5 volts reference circuit between the
ECM (pin 87 of E-12) and the FRP sensor (pin
3 of E-19) for an open circuit or high
resistance.

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 12

Go to Step 9

8

1.

Inspect for an intermittent and for a poor
connection at the harness connector of the
FRP sensor (pin 3 of E-19).

2.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 12

Go to Step 10

9

1.

Turn OFF the ignition.

2.

Disconnect the ECM harness connector.

3.

Inspect for an intermittent and for a poor
connection at the harness connector of the
ECM (pin 87 of E-12).

4.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 12

Go to Step 11

10

Replace the FRP sensor. Refer to Fuel Pressure
Sensor in Section 1D Engine Fuel.

Did you complete the replacement?

—

Go to Step 12

—

11

Important:

Replacement ECM must be

programmed.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 12

—

12

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 13

13

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 129

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
130
131
132
133
134
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: UNITED Страницы: 8

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

Бренд: RADVision Страницы: 3

Бренд: RADEMACHER Страницы: 48

Бренд: R&M Страницы: 53

Бренд: Rain Bird Страницы: 138

Бренд: Bartlett Страницы: 7

TruPortal TP-ADD-1DIP

Бренд: Interlogix Страницы: 9

Бренд: National Instruments Страницы: 14

Бренд: EFI Страницы: 127

Бренд: maxxess Страницы: 11

Бренд: SOLARJACK Страницы: 14

TempMaster M2 Plus Series

Бренд: Mold-Masters Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды