Isuzu 2008MY N Series Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 404

background image

Engine Control System (4HK1) 1A-75

3

1.

Turn OFF the ignition.

2.

Place the transmission in Neutral and set the
parking brake.

3.

Start the engine.

4.

Accelerate the engine between idle and
W.O.T. (accelerator pedal full travel) many
times while observing the DTC Information
with a scan tool.

Does the DTC fail this ignition?

—

Go to Step 4

An intermittent

problem by foreign

material in the fuel

system is

suspected. Go to

Step 13

4

1.

Turn OFF the ignition.

2.

Wait 1 minute for the fuel pressure to bleed
down from the fuel rail.

3.

Turn ON the ignition, with the engine OFF.

4.

Observe the Fuel Rail Pressure (FRP) Sensor
parameter with the scan tool.

Does the scan tool indicate within the
specified value?

0.9 to 1.0 volt

Go to Step 5

Go to Step 12

5

1.

Start the engine.

2.

Perform the Cylinder Balance Test with a scan
tool.

3.

Command each injector OFF and verify an
engine speed change for each injector.

Is there an injector that does not change
engine speed when commanded OFF?

—

Go to Step 15

Go to Step 6

6

1.

Inspect the fuel system line connections
between the fuel tank and the fuel supply
pump for tightness and all fuel hoses for cuts,
cracks and for the use of proper clamps.

Notice:

The fuel system from the fuel tank(s)

to the fuel supply pump is under a slight
vacuum with the engine running. As a result,
air can enter the fuel system if these
connections are not tight. Air in the fuel
system will cause fuel rail pressure
fluctuations especially at high engine speed
and load, which may set this DTC.

2.

Pump the priming pump until it becomes firm.
If there is a leak on the suction side of the fuel
system between the priming pump and the
fuel supply pump, the priming pump will not
build up sufficient firmness and fuel leakage
may occur.

3.

Start the engine and check for high side fuel
system leaks at the fuel supply pump and fuel
rail.

Notice:

Fuel may leak under the cylinder head

cover from the inlet high pressure line. In such
case, the engine oil level will rise. Inspect for
fuel leakage into the engine oil.

4.

Repair any fuel system leaks as necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 7

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 75

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
76
77
78
79
80
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: Eaton Страницы: 100

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: tams elektronik Страницы: 12

M16/RM N.C. DN 65 EEX

Бренд: Madas Страницы: 44

Бренд: Panasonic Страницы: 8

PetroVend PV200

Бренд: OPW Страницы: 2

MagicSpeed Series

Бренд: Waeco Страницы: 76

Бренд: Brand Innovations Страницы: 56

Бренд: Contec Страницы: 7

Бренд: Digiplex Страницы: 48

Бренд: Moog Страницы: 15

Бренд: YASKAWA Страницы: 35

I/O-SYSTEM 750-610

Бренд: WAGO Страницы: 14

Бренд: B meters Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды