Isuzu 2008MY N Series Скачать руководство пользователя страница 207 | Manualshive

Страница: 207 / 404

background image

1A-204 Engine Control System (4HK1)

2

1.

Install a scan tool.

2.

Turn OFF the ignition for 30 seconds.

3.

Start the engine.

4.

Monitor the DTC Information with a scan tool.

Does the DTC fail this ignition?

—

Go to Step 3

Go to Diagnostic

Aids

3

1.

Turn OFF the ignition for 30 seconds.

2.

Disconnect the VSS harness connector.

3.

Turn ON the ignition, with the engine OFF.

Is DTC P0502 also set?

—

Go to Step 4

Go to Step 5

4

Connect a test lamp between the low reference
circuit (pin 2 of J-48) and battery voltage.

Does the test lamp illuminate?

—

Go to Step 7

Go to Step 6

5

1.

Test the signal circuit between the ECM (pin
19 of J-14) and the VSS (pin 3 of J-48) for a
short to battery or ignition voltage.

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 10

Go to Step 9

6

Repair the open circuit or high resistance on the
low reference circuit between the VSS (pin 2 of J-
48) and ground terminal. Clean or tighten ground
as necessary.

Did you complete the repair?

—

Go to Step 10

—

7

1.

Inspect for an intermittent and for a poor
connection at the harness connector of the
VSS (pin 2 of J-48).

2.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 10

Go to Step 8

8

Replace the VSS. Refer to Vehicle Speed Sensor in
Section 9E Instrumentation/Driver Info.

Did you complete the replacement?

—

Go to Step 10

—

9

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 10

—

10

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 11

11

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 204

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
205
206
207
208
209
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: FrSky Страницы: 2

Бренд: Accu-Sort Страницы: 22

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Datavideo Страницы: 8

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: HALDER Страницы: 2

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: Saab Страницы: 4

Бренд: VAT Страницы: 39

Бренд: Samson Страницы: 124

Бренд: Samson Страницы: 86

Бренд: VAC Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды