Isuzu 2008MY N Series Скачать руководство пользователя страница 328

Страница: 328 / 404

Engine Control System (4HK1) 1A-325

Remove the glow relay.

Inspect for an intermittent and for poor
connection on each glow relay terminal.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 16

Go to Step 14

Replace the glow relay.

Did you complete the replacement?

—

Go to Step 16

—

Replace the appropriate glow plug.

Did you complete the replacement?

—

Go to Step 16

—

Reconnect all previously disconnected
components, relay, fuse or harness
connector(s).

Turn OFF the ignition for 30 seconds.

Turn ON the ignition, with the engine OFF.

Connect a test lamp between the metal bus
bar (glow plug power supply E-14 connector)
and a known good ground.

Perform the Glow Relay Control with a scan
tool.

Command the relay ON while observing the
test lamp.

Does the test lamp turn ON only when
commanded ON?

—

Go to Step 4

Go to Step 2

Step

Action

Value(s)

Yes

LG4HKED-WE-0871.book 325

ページ

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды

Isuzu 2008MY N Series, Руководство по ремонту

Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды