Isuzu 2008MY N Series Скачать руководство пользователя страница 103

Страница: 103 / 404

1A-100 Engine Control System (4HK1)

Connect a 3-amp fused jumper wire between the
12 volts reference circuit and the signal circuit (pins
1 and 3 of J-38).

Is the MAF Sensor parameter more than the
specified value?

4.9 volts

Go to Step 8

Go to Step 7

Test the 12 volts reference circuit between the
ECM (pin 23 of J-14) and the MAF sensor (pin
1 of J-38) for an open circuit or high
resistance.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 12

Go to Step 9

Test the signal circuit between the ECM (pin
69 of J-14) and the MAF sensor (pin 3 of J-38)
for the following conditions:

• An open circuit
• A short to ground
• A short to the low reference circuit
• High resistance

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 12

Go to Step 9

Inspect for an intermittent and for poor
connections at the harness connector of the
MAF sensor (pins 1 and 3 of J-38).

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 12

Go to Step 10

Turn OFF the ignition.

Disconnect the ECM harness connector.

Inspect for an intermittent and for poor
connections at the harness connector of the
ECM (pins 23 and 69 of J-14).

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 12

Go to Step 11

Replace the MAF sensor. Refer to MAF/IAT Sensor
in Section 1J Induction.

Did you complete the replacement?

—

Go to Step 12

—

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 12

—

Reconnect all previously disconnected
harness connector(s).

Clear the DTCs with a scan tool.

Turn OFF the ignition for 30 seconds.

Start the engine.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 13

Step

Action

Value(s)

Yes

LG4HKED-WE-0871.book 100

ページ

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды

Isuzu 2008MY N Series, Руководство по ремонту

Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды