manualshive.com logo in svg

Isuzu 2008MY N Series, Руководство по ремонту

Руководство по ремонту и эксплуатации Isuzu 2008MY N Series доступно для бесплатной загрузки с {веб-сайта}. Этот мануал содержит подробные инструкции по обслуживанию и ремонту вашего автомобиля, помогая сохранить его в отличном состоянии. Получите свой экземпляр прямо сейчас и узнайте все тонкости ухода за вашим Isuzu.

Поделиться
Скачать
background image

1A-374    Engine Control System (4HK1) 

c. Launch the TIS application.
d. Select the Security Access at the main screen.
e. Highlight the “Tech 2” on the Diagnostic Tool

Selection screen and click “Next”.

f. Click “Close” on the Security Access Enabled

screen.

g. Turn OFF the scan tool.
h. Disconnect the scan tool from the terminal.

5. After complete the programming, turn OFF the

ignition for 30 seconds.

6. Start the engine and let idle.
7. Inspect for a proper engine running condition and

for no DTC's. Refer to the Diagnostic System
Check - Engine Controls if needed.

D-2. Programming Fuel Injector ID Codes and VIN

1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Select Diagnostics > appropriate vehicle

identification > 4HK1 > Programming > Replace
Injector.

4. If except Euro 4 spcecification, skip to step 8. In

order to get programming approval, the on-screen
displays a message to user. Get programming
approval from the TIS 2000 using the following
procedure:
a. Connect a scan tool to the terminal that

installed TIS 2000 with the latest software and
the hardware key is plugged into port.

b. Turn ON the scan tool and keep at title screen.
c. Launch the TIS application.
d. Select the Security Access at the main screen.
e. Highlight the “Tech 2” on the Diagnostic Tool

Selection screen and click “Next”.

f. Click “Close” on the Security Access Enabled

screen.

g. Turn OFF the scan tool.
h. Disconnect the scan tool from the terminal.

5. Install a scan tool to the vehicle.
6. Turn ON the ignition, with the engine OFF.
7. Select Diagnostics > appropriate vehicle

identification > 4HK1 > Programming > Replace
Injector.

8. Input 24 digits of each fuel injector ID code.
9. Select Program VIN. Verify the VIN on the screen if

programmed at previously described SPS. If not
programmed or incorrect VIN, input correct VIN.

10. After complete the programming, turn OFF the

ignition for 30 seconds.

11. Start the engine and let idle.

12. Inspect for a proper engine running condition and

for no DTC's. Refer to the Diagnostic System
Check - Engine Controls if needed.

E. Supply Pump Relearn

1. Install a scan tool.
2. Start the engine and let idle until engine coolant

temperature reads 65

°

C (149

°

F) or higher while

observing the Supply Pump Status parameter with
a scan tool. The scan tool parameter changes
status Not Learned > Learned.

Service Programming System (SPS)
Description

The service programming system (SPS) allows a
technician to program a control module through the
data link connector (DLC). The information transfer
circuit that is used at the DLC is the same serial data
circuit used by the scan tool for retrieving DTCs,
displaying data, clearing DTCs etc. This procedure
offers the ability to install software/ calibrations
matched to a particular vehicle.
Most control modules have two types of memory. The
software/ calibrations reside in the flash memory. The
two types of memory are listed below:

• Electrically Erasable Programmable Read Only

Memory (EEPROM)
This type of memory allows selected portions of
memory to be programmed while other portions
remain unchanged.
Certain learned values reside in the EEPROM,
such as:

- The vehicle identification number (VIN)
- The software/ calibrations identification

numbers

- The control module security information

• Flash Read Only Memory-Flash Memory

Flash memory has increased memory storage
capacity. During programming, all information
within this type of memory is erased, and then
replaced with entirely new information.

Service Programming Methods

The two methods of programming a ECM are listed
below:

• Remote Programming
• Pass Thru Programming

For information on programming an ECM using one of
the methods listed above, refer to Service
Programming System (SPS) (Remote Procedure) or
Service Programming System (SPS) (Pass-Thru
Procedure).

Before Programming a Control Module
Important: 

DO NOT program an existing ECM with the

identical software/ calibration package. This procedure
is not a short cut to correct the driveability condition.
This is an ineffective repair. An ECM should only be
programmed when the following occurs:

LG4HKED-WE-0871.book  374 

ページ

  

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

S&C 6800 Series Instruction Sheet preview
6800 Series
Бренд: S&C Страницы: 40
NCR 1651 Quick Reference Manual preview
1651
Бренд: NCR Страницы: 6
Eaton SC100 Operation Handbook preview
SC100
Бренд: Eaton Страницы: 86
Waters 2690 Quick Start Manual preview
2690
Бренд: Waters Страницы: 55
Paradox IP150 Programming Manual preview
IP150
Бренд: Paradox Страницы: 2
GANTERUD L3 User Manual preview
L3
Бренд: GANTERUD Страницы: 24
Harmar Mobility Pinnacle Installation And Service Manual preview
Pinnacle
Бренд: Harmar Mobility Страницы: 16
Gardigo 80000 Instruction Manual preview
80000
Бренд: Gardigo Страницы: 8
Gardigo 60035 Instruction Manual preview
60035
Бренд: Gardigo Страницы: 19
Rain Bird PAR+ES Installation Manual preview
PAR+ES
Бренд: Rain Bird Страницы: 24
Rain Bird ESP-LXIVM Series Device Installation Manuallines preview
ESP-LXIVM Series
Бренд: Rain Bird Страницы: 16
RADVision SCOPIA 400 Platform Manual preview
SCOPIA 400
Бренд: RADVision Страницы: 39
QNAP KoiBox-100W Quick Start Manual preview
KoiBox-100W
Бренд: QNAP Страницы: 35
Rabe PILOT Original Instructions Manual preview
PILOT
Бренд: Rabe Страницы: 61
Racal Instruments 1260 VXI Instructions Manual preview
1260 VXI
Бренд: Racal Instruments Страницы: 35
YOKOGAWA UT35A-L User Manual preview
UT35A-L
Бренд: YOKOGAWA Страницы: 150
YOODA NANO Series Quick Start Manual preview
NANO Series
Бренд: YOODA Страницы: 3
YMGI 584 Series User Manual preview
584 Series
Бренд: YMGI Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды