Isuzu 2008MY N Series Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 404

background image

Engine Control System (4HK1) 1A-83

12

1.

Turn OFF the ignition.

2.

Disconnect the FRP sensor harness
connector.

3.

Inspect for an intermittent, for poor
connections and corrosion at the harness
connector of the FRP sensor (pins 1, 2 and 3
of E-19).

4.

Disconnect the ECM harness connector.

5.

Inspect for an intermittent, for poor
connections and corrosion at the harness
connector of the ECM (pins 82, 87, 90 and
101 of E-12).

6.

Test for high resistance on each circuit.

7.

Repair the connection(s) or circuit(s) as
necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 14

13

Replace the fuel filter element. Refer to Fuel Filter
Element in Section 1D Engine Fuel .

Did you complete the replacement?

—

Go to Step 17

—

14

Replace the FRP sensor. Refer to Fuel Pressure
Sensor in Section 1D Engine Fuel.

Did you complete the replacement?

—

Go to Step 17

—

15

Important:

Replacement fuel injector must be

programmed.
Replace the appropriate fuel injector that does not
change engine speed when commanded OFF.
Refer to Injector in Section 1D Engine Fuel.

Did you complete the replacement?

—

Go to Step 17

—

16

Important

: The fuel supply pump must be timed to

the engine and adjustment value must be learned
to the ECM.

Notice:

Always replace the fuel filter element when

a fuel supply pump is replaced.
Replace the fuel supply pump and fuel filter
element. Refer to Fuel Supply Pump and Fuel Filter
Element in Section 1D Engine Fuel.

Did you complete the replacement?

—

Go to Step 17

—

17

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 2

Go to Step 18

18

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 83

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
84
85
86
87
88
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Concord express

Бренд: GE Страницы: 3

ServeRAID M5014

Бренд: IBM Страницы: 106

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: janitza Страницы: 58

Бренд: Lab.gruppen Страницы: 2

Бренд: Partizan Страницы: 7

Бренд: cinetto Страницы: 56

Cutler-Hammer LMR

Бренд: Eaton Страницы: 38

Бренд: DNF Controls Страницы: 22

Бренд: Matelec Страницы: 2

DX99N9X1S2N0M2X0D2

Бренд: Banner Страницы: 13

Бренд: Napa Страницы: 15

Бренд: FAAC Страницы: 63

Бренд: Kontron Страницы: 92

AMES 660GD-15-17

Бренд: Watts Страницы: 12

EZ Power Remote

Бренд: Pogo Страницы: 1

Бренд: Radio Shack Страницы: 16

Бренд: Parker Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды