Isuzu 2008MY N Series Скачать руководство пользователя страница 254 | Manualshive

Страница: 254 / 404

background image

Engine Control System (4HK1) 1A-251

DTC P1664 (Flash Code 76)

Circuit Description

The service vehicle soon (SVS) lamp is located on the
instrument panel (IP) cluster. The SVS lamp informs
the driver that a non-emission related fault has
occurred and vehicle service required.
The ECM monitors the SVS lamp control circuit for
conditions that are incorrect for the commanded state
of the SVS lamp. For example, a failure condition exists
if the ECM detects low voltage when the SVS lamp is
commanded OFF, or high voltage when the SVS lamp
is commanded ON. If the ECM detects an improper
voltage level on the control circuit, this DTC will set.

Condition for Running the DTC

• The battery voltage is between 18 to 32 volts.
• The ignition switch is ON.

Condition for Setting the DTC

Either of following condition is met:

• The ECM detects a low voltage condition on the

SVS lamp control circuit when the lamp is
commanded OFF.

• The ECM detects a high voltage condition on the

SVS lamp control circuit when the lamp is
commanded ON.

Action Taken When the DTC Sets

• The ECM will illuminate the SVS lamp. Refer to

DTC Type Definitions for Action Taken when the
DTC Sets - Type C.

Condition for Clearing the DTC

• Refer to DTC Type Definitions for Condition for

Clearing the SVS Lamp/ DTC - Type C.

Diagnostic Aids

• If an intermittent condition is suspected, refer to

Intermittent Conditions in this section.

Schematic Reference:

Engine Controls Schematics

Connector End View Reference:

Engine Controls

Connector End Views or ECM Connector End Views

Circuit/ System Testing DTC P1664

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check
- Engine Controls?

—

Go to Step 2

Go to Diagnostic

System Check -
Engine Controls

2

1.

Verify whether the instrument panel (IP)
cluster is operational.

2.

Install a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Turn ON the ignition for 10 seconds.

5.

Start the engine.

6.

Monitor the DTC Information with a scan tool.

Does the DTC fail this ignition?

—

Go to Step 3

Go to Diagnostic

Aids

3

1.

Turn OFF the ignition.

2.

Inspect the Meter (10A) fuse in the cab.

Is the Meter (10A) fuse open?

—

Go to Step 4

Go to Step 5

4

Replace the Meter (10A) fuse. If the fuse continues
to open, repair the short to ground on one of the
circuits that is fed by the Meter (10A) fuse or
replace the shorted attached component.

Did you complete the repair?

—

Go to Step 17

—

5

1.

Turn OFF the ignition.

2.

Disconnect the ECM J-14 harness connector.

3.

Turn ON the ignition, with the engine OFF.

Is the SVS lamp OFF?

—

Go toStep 6

Go to Step 12

LG4HKED-WE-0871.book 251

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
252
253
254
255
256
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: Magnescale Страницы: 132

Бренд: Rane Страницы: 2

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

1E0671-1 MCR2.9

Бренд: Haberl Electronic Страницы: 9

Бренд: J+J Страницы: 2

Бренд: Abocom Страницы: 10

Бренд: Gardigo Страницы: 6

Бренд: VAT Страницы: 14

Бренд: DSE Страницы: 2

Centronic SunWindControl SWC245-II

Бренд: Becker Страницы: 52

CentralControl CC41

Бренд: Becker Страницы: 48

Бренд: GSK Страницы: 32

ibaMS16-DI-220V Series

Бренд: IBA Страницы: 32

Бренд: Omniflex Страницы: 2

Бренд: IFM Страницы: 41

Бренд: Duco Страницы: 16

Бренд: Vaniman Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды