Isuzu 2008MY N Series, Руководство по ремонту

Страница: 379 / 404

1A-376 Engine Control System (4HK1)
• Select Programming Process - Identify
whether an existing ECM is being
reprogrammed or an ECM is being replaced
with a new one
• Select ECU Location - Vehicle
e. Verify the connections on the Preparing for
Communication screen, then click "Next".
f. Verify the VIN on the Validate Vehicle
Identification Number (VIN) screen, then click
"Next".
Notice: If the ECM is replaced to new one, VIN
does not displayed. Input correct VIN reading
from stamped VIN or affixed VIN plate on the
vehicle. If the ECM from another vehicle is
installed, input correct VIN by same way.
g. Highlight Engine on the Select System Type
screen, then click "Next", if on-screen
instruction displayed.
h. Complete the following information based on
the service ID plate on the Validate Vehicle
Data screen until "Next" is highlighted, then
click "Next".
• Model
• Model year
• Engine type
• Model designator
• Destination code
• Transmission type
i. Verify your selection on the Summary screen.
Notice: Refer to Service Bulletin and
Description column before service
programming is performed if the bulletins are
listed along with the calibration files.
Notice: Select Cancel if you receive a message
stating that the calibration selected is already
the current calibration in the ECM and
reprogramming with the same download is not
allowed.
j. Click "Reprog".
k. The Transfer Data screen will appear until the
progress bar reaches 100%.
5. Close the application and return to the TIS
application selection screen after the download is
complete.
6. Turn OFF the scan tool and disconnect from the
terminal.
7. Transfer the data from the scan tool to the ECM
using the following procedure:
a. Install a scan tool.
b. Turn ON the ignition, with the engine OFF.
c. Select Service Programming System (SPS) >
Program ECU.
d. Turn OFF all accessories and press "Continue".
e. Programming in Process will appear until the
progress bar reaches 100%.
Notice: Some warning lamp may turn ON or
blink while programming the ECM since
communication between the ECM and other
modules are interrupted. Clear DTC in any
module after programming.
f. Press "Continue" and exit the program after the
scan tool displays "Programming Was
Successful".
8. Turn OFF the ignition.
9. Turn OFF the scan tool and disconnect from the
vehicle.
Service Programming System (SPS) (Pass-
Thru Procedure)
Pass-Thru programming allows the scan tool to remain
connected to the terminal and to the vehicle throughout
the programming process. The vehicle must be in close
proximity to the terminal while using Pass-Thru.
1. Launch the TIS application.
2. Select the Service Programming System at the
main screen.
3. Highlight the following information on the Select
Diagnostic Tool and Programming Process screen,
then click "Next":
• Select Diagnostic Tool-Select Pass - Thru
• Select Programming Process - Identify whether
as existing ECM is being reprogrammed or an
ECM is being replaced with a new one.
• Select ECU Location - Vehicle
4. Complete all vehicle data on the Preparing for
Communication/ Determine Vehicle screen until
"Next" is highlighted, then click "Next".
5. Follow the instruction on the Preparing for
Communication screen, then click "Next".
Notice: In order to reduce the potential for signal
loss, the RS-232 cable should not be more than 25
feet long.
6. Verify the VIN on the Validate Vehicle Identification
Number (VIN) screen, then click "Next".
Notice: If the ECM is replaced to new one, VIN
does not displayed. Input correct VIN reading from
stamped VIN or affixed VIN plate on the vehicle. If
the ECM from another vehicle is installed, input
correct VIN by same way.
7. Highlight Engine on the Select System Type
screen, then click "Next", if on-screen instruction
displayed.
8. Complete the following information based on the
service ID plate on the Validate Vehicle Data
screen until "Next" is highlighted, then click "Next".
LG4HKED-WE-0871.book 376 ページ ２００７年１１月２９日 木曜日 午後６時２９分