Isuzu 2008MY N Series Скачать руководство пользователя страница 319 | Manualshive

Страница: 319 / 404

background image

1A-316 Engine Control System (4HK1)

6

1.

Turn OFF the ignition.

2.

Disconnect the electric hydraulic control unit
(EHCU) harness connector if installed.

3.

Disconnect the transmission control module
(TCM) harness connectors if installed.

4.

Disconnect the data recording module (DRM)
or body control modul (BCM) harness
connector .

5.

Turn ON the ignition, with the engine OFF.

6.

Connect a DMM between the CAN Low circuit
(pin 16 of E-4) and a known good ground.

7.

Connect a DMM between the CAN High circuit
(pin 15 of E-4) and a known good ground.

8.

Test the CAN Low and High circuits (which
ever voltage reading did not read within the
specified value) between the ECM (pins 18
and 37 of J-14) and the VNT control module
(pins 15 and 16 of E-4) for an open circuit or
high resistance.

9.

Repair the circuit(s) or connection(s) as
necessary.

Did you find and correct the condition?

1.5 to 3.5

volts

Go to Step 17

Go to Step 13

7

1.

Test the CAN Low and High circuits between
the IP cluster (pins 13 and 14 of B-105) and
the joint connection for an open circuit or high
resistance.

2.

Inspect for an intermittent, for poor
connections and corrosion at the harness
connector of the IP cluster (pins 13 and 14 of
B-105).

3.

Repair the circuit(s) or connection(s) as
necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 12

8

1.

Connect a DMM between the ignition voltage
feed circuit to the VNT control module (pin 13
of E-4) and a known good ground.

2.

Turn ON the ignition, with the engine OFF.

Is the DMM voltage more than the specified
value?

20.0 volts

Go to Step 9

Go to Step 10

9

Connect a DMM across the ignition voltage feed
circuit and ground circuit (pins 13 and 14 of E-4).

Is the DMM voltage more than the specified
value?

20.0 volts

Go to Step 12

Go to Step 11

10

Repair the open circuit or high resistance between
the ECM (15A) fuse and the VNT control module
(pin 13 of E-4). Check the ECM (15A) fuse first.

Did you complete the repair?

—

Go to Step 17

—

11

Repair the open circuit or high resistance between
the VNT control module (pin 14 of E-4) and the
ground terminal (E-9). Clean or tighten ground as
necessary.

Did you complete the repair?

—

Go to Step 17

—

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 316

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
317
318
319
320
321
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

WAGO-I/O-SYSTEM 750 XTR Series

Бренд: WAGO Страницы: 272

Бренд: WAGO Страницы: 450

Бренд: TagMaster Страницы: 28

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: Gardena Страницы: 236

ibaMS16-DI-220V Series

Бренд: IBA Страницы: 32

Бренд: Eaton Страницы: 2

Бренд: Festo Страницы: 14

Бренд: nedis Страницы: 56

Бренд: Azbil Страницы: 68

Бренд: Ltech Страницы: 2

Бренд: IBC control Страницы: 16

Бренд: Kaelus Страницы: 52

Бренд: ETI Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды