Isuzu 2008MY N Series Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 404

background image

Engine Control System (4HK1) 1A-141

13

1.

Test the cylinder #4 fuel injector circuit
between the fuel injector terminals and the in-
line harness connector for the following
conditions:

• An open circuit
• A short circuit each other
• High resistance

2.

Repair the circuit(s) or replace the fuel injector
harness as necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 15

14

1.

Turn OFF the ignition.

2.

Disconnect the ECM harness connector.

3.

Inspect for an intermittent and for a poor
connection at the harness connector of the
ECM.

4.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 16

15

Important:

Replacement fuel injector must be

programmed.
Replace the cylinder #4 fuel injector. Refer to
Injector in Section 1D Engine Fuel.

Did you complete the replacement?

—

Go to Step 17

—

16

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 17

—

17

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 18

18

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 141

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
142
143
144
145
146
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: FAAC Страницы: 14

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

PowerXL DX-NET-ETHERCAT-2

Бренд: Eaton Страницы: 3

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Q-SYS Core 110f

Бренд: QSC Страницы: 2

Бренд: Ziton Страницы: 28

Бренд: Unico Страницы: 164

Бренд: DANIEL Страницы: 48

Бренд: GEA Страницы: 47

Бренд: Zaiput Flow Technologies Страницы: 10

CPX-AP-A-16DI-D-M12-5P

Бренд: Festo Страницы: 16

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды