Isuzu 2008MY N Series Скачать руководство пользователя страница 290 | Manualshive

Страница: 290 / 404

background image

Engine Control System (4HK1) 1A-287

5

1.

Turn OFF the ignition.

2.

Disconnect the exhaust differential pressure
sensor harness connector.

3.

Inspect for an intermittent, for poor
connections and corrosion at the harness
connector of the exhaust differential pressure
sensor (pins 1, 2 and 3 of J-33).

4.

Disconnect the ECM harness connector.

5.

Inspect for an intermittent, for poor
connections and corrosion at the harness
connector of the ECM (pins 67, 79 and 80 of
J-14).

6.

Test each sensor circuit between the ECM and
the exhaust differential pressure sensor for
high resistance.

7.

Repair the connection(s) or circuit(s) as
necessary.

Did you find and correct the condition?

—

Go to Step 7

Go to Step 6

6

Replace the exhaust differential pressure sensor.
Refer to Exhaust Differential Pressure Sensor in
Section 1G Engine Exhaust.

Did you complete the replacement?

—

Go to Step 7

—

7

1.

Reconnect all previously disconnected
harness connector(s) or components.

2.

Turn ON the ignition for 30 seconds. DO NOT
start the engine. (This is to relearn exhaust
differential pressure sensor.)

3.

Clear the DTC and reset the DPD Status with
a scan tool.

4.

Turn OFF the ignition for 30 seconds.

5.

Perform the DPD Regeneration with a scan
tool. If the DPD filter was replaced at Step 4,
skip to Step 9.

Did you complete the action?

—

Go to Step 8

—

8

1.

Observe the Exhaust Temperature 1
parameter with a scan tool. Make sure the
temperature is less than 150

°

C (302

°

F). If

more than 150

°

C (302

°

F), let increase 1500

RPM without load. (Turn the idle up control
knob clockwise.)

2.

Accelerate the engine to W.O.T. (accelerator
pedal full travel) and read the Exhaust
Differential Pressure parameter when the
Exhaust Temperature 1 parameter is reached
to 200

°

C (392

°

F).

Is the Exhaust Differential Pressure parameter
more than the specified value?

1.0 kPa

Go to Step 9

Go to Step 2

9

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 287

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
288
289
290
291
292
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: NCR Страницы: 6

Бренд: Eaton Страницы: 16

Бренд: Caen Страницы: 20

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: National Instruments Страницы: 29

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

Hard Top Lifter

Бренд: Garage Smart Страницы: 20

Бренд: Tamas Страницы: 12

Бренд: Tait Страницы: 3

Бренд: Polycom Страницы: 2

traxon e:cue LCE-mx

Бренд: Osram Страницы: 35

Бренд: tell Страницы: 11

Бренд: DSC Страницы: 16

Бренд: D+H Страницы: 2

Бренд: GRAUPNER Страницы: 180

Бренд: Grandstream Networks Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды