Isuzu 2008MY N Series Скачать руководство пользователя страница 314 | Manualshive

Страница: 314 / 404

background image

Engine Control System (4HK1) 1A-311

17

Replace the IP cluster. Refer to Instrument Panel
(IP) Cluster in Section 9E Instrumentation/Driver
Info.

Did you complete the replacement?

—

Go to Step 23

—

18

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 23

—

19

Replace the VNT control module.

Did you complete the replacement?

—

Go to Step 23

—

20

Replace the EHCU. Refer to EHCU in Section 4C1
ABS/ASR .

Did you complete the replacement?

—

Go to Step 23

—

21

Important:

Replacement BCM must be

programmed.
Replace the DRM or BCM. If the BCM is installed,
refer to BCM in Section 10B Vehicle Control.

Did you complete the replacement?

—

Go to Step 23

—

22

Important:

Replacement TCM must be

programmed and learned.
Replace the TCM. Refer to TCM in Section 5A
Transmission Control System.

Did you complete the replacement?

—

Go to Step 23

—

23

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 24

24

Observe the DTC information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 311

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
312
313
314
315
316
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: Lattice Semiconductor Страницы: 30

Бренд: WAFER Страницы: 15

Бренд: Saga Страницы: 9

Бренд: Parker Страницы: 44

Бренд: ICM Controls Страницы: 2

Бренд: IDTECK Страницы: 12

Бренд: Banner Страницы: 2

CGLine+ Web Controller

Бренд: Eaton Страницы: 28

Бренд: Jetter Страницы: 24

Бренд: Challenger Lifts Страницы: 20

MagicSpeed Series

Бренд: Waeco Страницы: 76

Бренд: Brand Innovations Страницы: 56

Бренд: Watlow Страницы: 20

Бренд: Grundfos Страницы: 23

Бренд: Sungrow Страницы: 4

Бренд: IR-Tec Страницы: 14

Бренд: Heat & Cool Страницы: 5

Бренд: Delta Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды