Isuzu 2008MY N Series Скачать руководство пользователя страница 342 | Manualshive

Страница: 342 / 404

background image

Engine Control System (4HK1) 1A-339

8

Important:

Reset the DPD Status before

regeneration with a scan tool.
Perform the DPD Regeneration with a scan tool.

Does the regeneration start?

—

Go to Step 10

ECM is not allowing

the DPD

regeneration

control. Refer to

Test Description and

DTC List

9

Important:

Reset the DPD Status before

regeneration with a scan tool.

Important:

Engine Oil must be replaced after DPD

slow regeneration is completed.
Perform the DPD Slow Regeneration with a scan
tool.

Does the regeneration start?

—

Go to Step 10

ECM is not allowing

the DPD

regeneration

control. Refer to

Test Description and

DTC List

10

Does the regeneration complete?

—

Go to Step 11

Go to Step 13

11

1.

Observe the Exhaust Temperature 1
parameter with a scan tool. Make sure the
temperature is less than 150

°

C (302

°

F). If

more than 150

°

C (302

°

F), let increase 1500

RPM without load. (Turn the idle up control
knob clockwise.)

2.

Accelerate the engine to W.O.T. (accelerator
pedal full travel) and read the Exhaust
Differential Pressure parameter when the
Exhaust Temperature 1 parameter is reached
to 200

°

C (392

°

F).

Is the Exhaust Differential Pressure parameter
less than the specified value?

5.9 kPa (low

output) 2.5

kPa (higt

output)

Go to Step 12

Ash cleaning must

be performed. Refer

to appropriate

procedure in

Section 1G Engine

Exhaust

12

Is the Exhaust Differential Pressure parameter
more than the specified value?

1.0 kPa

System OK

Refer to DTC P2452

13

Notice:

If the scan tool displays a message "The

failure in which compulsive regeneration is
impossible was detected", go to applicable DTC.
1.

Remove the DPD filter from the DPD
assembly. Refer to Exhaust Pipe in Section
1G Engine Exhaust. Inspect the following
conditions:

• DPD filter for damage, cranks or melt
• Oxygen catalyst for damage, cranks melt

or excessive deposits

• Deteriorated oxygen catalyst

2.

Test the engine cooling system for an
overheating condition. Refer to Cooling
System in Section 1C Engine Cooling.

3.

Inspect the fuel system problem. Refer to Fuel
System Check chart and appropriate
procedure in Section 1D Engine Fuel.

4.

Repair or replace as necessary.

Did you complete the action?

—

Go to Step 14

—

14

Reconnect all previously disconnected components
or harness connector(s).

Did you complete the action?

—

Go to Step 5

—

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 339

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
340
341
342
343
344
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

DELTAFLUX MT100

Бренд: PIETRO FIORENTINI Страницы: 16

Бренд: Waters Страницы: 55

Бренд: Paradox Страницы: 2

Бренд: GANTERUD Страницы: 24

Бренд: Warren Controls Страницы: 16

Бренд: Laars Страницы: 28

Бренд: M-system Страницы: 3

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 13

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

Бренд: Oceanic Systems Страницы: 8

Бренд: WAGNER Страницы: 128

Бренд: AUMA Страницы: 24

Бренд: VALSTEAM ADCA Страницы: 4

Бренд: Sielco Elettronica Страницы: 15

Бренд: M-system Страницы: 7

Бренд: D+H Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды