Isuzu 2008MY N Series Скачать руководство пользователя страница 227

Страница: 227 / 404

1A-224 Engine Control System (4HK1)

Remove the Meter (10A) fuse that supplies
voltage to the MIL.

Turn ON the ignition, with the engine OFF.

Measure the voltage from the MIL control
circuit in the ECM harness connector (pin 6 of
J-14) to a known good ground.

Is the voltage less than the specified value?

1 volt

Go to Step 7

Go to Step 13

Turn OFF the ignition.

Reinstall the Meter (10A) fuse.

Turn ON the ignition, with the engine OFF.

Connect a 3-amp fused jumper wire between
the ECM harness connector (pin 6 of J-14)
and a known good ground.

Is the MIL illuminated?

—

Go to Step 11

Go to Step 8

Connect a test lamp between the ignition
voltage feed circuit of the IP cluster harness
connector (pin 2 of B-105) and a known good
ground.

Turn ON the ignition, with the engine OFF.

Does the test lamp illuminate?

—

Go to Step 9

Go to Step 14

Test the control circuit between the ECM (pin
6 of J-14) and the IP cluster (pin 31 of B-105)
for an open circuit or high resistance.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 10

Inspect for an intermittent and for poor
connections at the harness connector of the
IP cluster (pins 2 and 31 of B-105).

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 15

Inspect for an intermittent and for a poor
connection at the harness connector of the
ECM (pin 6 of J-14).

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 17

Go to Step 16

Repair the short to ground between the ECM (pin 6
of J-14) and the IP cluster (pin 31 of B-105).

Did you complete the repair?

—

Go to Step 17

—

Repair the short to battery or ignition voltage
between the ECM (pin 6 of J-14) and the IP cluster
(pin 31 of B-105).

Did you complete the repair?

—

Go to Step 17

—

Repair the open circuit or high resistance on
ignition the voltage feed circuit between the Meter
(10A) fuse and the IP cluster (pin 1 of B-105).

Did you complete the repair?

—

Go to Step 17

—

Repair or replace the IP cluster. Refer to Instrument
Panel (IP) Cluster in Section 9E Instrumentation /
Driver Info.

Did you complete the repair or replacement?

—

Go to Step 17

—

Step

Action

Value(s)

Yes

LG4HKED-WE-0871.book 224

ページ

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды

Isuzu 2008MY N Series, Руководство по ремонту

Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды