Isuzu 2008MY N Series Скачать руководство пользователя страница 64

Страница: 64 / 404

Engine Control System (4HK1) 1A-61

Test the battery voltage circuit between the
ECM (pins 2 and 5 of J-14) and the ECM main
relay for the following conditions:

• An open circuit
• High resistance or a poor connection at

the ECM or ECM main relay

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 15

Go to Step 14

Replace the ECM main relay.

Did you complete the replacement?

—

Go to Step 15

—

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 15

—

Turn OFF the ignition.

Reconnect all previously disconnected fuse,
relay or harness connector(s).

Turn ON the ignition, with the engine OFF.

Attempt to establish communication with the
ECM.

Does the scan tool communicate with the
ECM?

—

System OK

Go to Step 3

Step

Action

Value(s)

Yes

LG4HKED-WE-0871.book 61

ページ

２００７年１１月２９日　木曜日　午後６時２９分

Содержание 2008MY N Series





















































































































































































































































































































































































































Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды

Isuzu 2008MY N Series, Руководство по ремонту

Результаты поиска

Содержание 2008MY N Series

Отзывы:

Похожие инструкции для 2008MY N Series

Бренды по названию

Популярные бренды