Isuzu 2008MY N Series Скачать руководство пользователя страница 216 | Manualshive

Страница: 216 / 404

background image

Engine Control System (4HK1) 1A-213

DTC P0602 (Flash Code 154)

Circuit Description

The electrically erasable & programmable read only
memory (EEPROM) memorizes fuel injector ID code
information. If the ECM detects fuel injector ID codes
are not programmed into the ECM or an error in the
programmed fuel injector ID codes, this DTC will set.

Condition for Running the DTC

• The ignition switch is ON.

Condition for Setting the DTC

Either of following condition is met:

• The ECM detects that the fuel injector ID code is

not programmed.

• The ECM detects an error in the programmed fuel

injector ID code.

Action Taken When the DTC Sets

• The ECM illuminates the SVS lamp when the

diagnostic runs and fails. Refer to DTC Type
Definitions for Action Taken When the DTC Sets -
Type C. (Euro 4 specification)

• The ECM illuminates the MIL when the diagnostic

runs and fails. Refer to DTC Type Definitions for
Action Taken When the DTC Sets - Type A.
(Except Euro 4 specification)

Condition for Clearing the DTC

• Refer to DTC Type Definitions for Condition for

Clearing the SVS Lamp/ DTC - Type C. (Euro 4
specification)

• Refer to DTC Type Definitions for Condition for

Clearing the MIL/ DTC - Type A. (Except Euro 4
specification)

Notice:

Clear the DTC with a scan tool after

programming the fuel injector ID code.

Circuit/ System Testing DTC P0602

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check
- Engine Controls?

—

Go to Step 2

Go to Diagnostic

System Check -
Engine Controls

2

1.

Ensure that all tool connections are secure.

2.

Ensure that programming equipment is
operating correctly.

3.

Install a scan tool.

4.

Turn OFF the ignition for 30 seconds.

5.

Turn ON the ignition, with the engine OFF.

6.

Monitor the DTC Information with a scan tool.

Does the DTC fail this ignition?

—

Go to Step 3

Go to Step 5

3

1.

Verify the correct fuel injector ID codes are
entered into the ECM with a scan tool. Refer
to ECM Replacement. If the fuel injector ID
codes are correctly entered, clear the DTC
with a scan tool.

2.

Turn OFF the ignition for 30 seconds.

3.

Turn ON the ignition, with the engine OFF.

Does the DTC fail this ignition?

—

Go to Step 4

Go to Step 5

4

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 5

—

LG4HKED-WE-0871.book 213

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
214
215
216
217
218
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: IBM Страницы: 276

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 157

Бренд: Magellan Страницы: 2

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: R. Beck Maschinenbau Страницы: 34

Бренд: Polycom Страницы: 2

Бренд: DigiPower Страницы: 27

Бренд: Measurement Computing Страницы: 32

Бренд: Heat & Cool Страницы: 5

Бренд: EBS Страницы: 118

IconRemote IR10A

Бренд: X10 Страницы: 21

Бренд: Genie Страницы: 35

Бренд: Ubiquiti Страницы: 16

Бренд: Samson Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды