Isuzu 2008MY N Series Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 404

background image

1A-106 Engine Control System (4HK1)

7

Important:

The boost pressure sensor may be

damaged if the sensor signal circuit is shorted to a
voltage source.
1.

Test the signal circuit between the ECM (pin
91 of E-12) and the boost pressure sensor
(pin 1 of E-24) for the following conditions:

• A short to battery or ignition voltage
• A short to any 5 volts reference

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 13

Go to Step 12

8

Notice:

The boost pressure sensor shares the low

reference circuit with other sensors. A fault
condition in the low reference circuit may set DTCs
on sensors that share this circuit.
1.

Test the low reference circuit between the
ECM (pin 109 of E-12) and the boost pressure
sensor (pin 2 of E-24) for an open circuit or
high resistance.

2.

Repair the circuit(s) as necessary.

Did you find and correct the condition?

—

Go to Step 13

Go to Step 10

9

1.

Inspect for an intermittent and for a poor
connection at the harness connector of the
boost pressure sensor (pin 2 of E-24).

2.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 13

Go to Step 11

10

1.

Turn OFF the ignition.

2.

Disconnect the ECM harness connector.

3.

Inspect for an intermittent and for a poor
connection at the harness connector of the
ECM (pin 109 of E-12).

4.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 13

Go to Step 12

11

Replace the boost pressure sensor. Refer to Boost
Pressure Sensor in Section 1J Induction.

Did you complete the replacement?

—

Go to Step 13

—

12

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 13

—

13

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 2

Go to Step 14

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 106

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
107
108
109
110
111
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: GCE Страницы: 24

Бренд: Eaton Страницы: 10

Бренд: Idemia Страницы: 29

Бренд: Lab.gruppen Страницы: 2

Бренд: Fox Страницы: 5

Бренд: MaintTech Страницы: 28

Бренд: GREER Company Страницы: 35

Бренд: Aurora Страницы: 2

ProducTVity Station

Бренд: red lion Страницы: 8

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

Бренд: Mesa Страницы: 58

Бренд: Trane Technologies Страницы: 8

Бренд: Safety Clamps Страницы: 16

Бренд: Case IH Страницы: 81

Бренд: PS Automation Страницы: 4

Бренд: Atmel Страницы: 12

Бренд: M-system Страницы: 7

Бренд: Waterbird Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды