Isuzu 2008MY N Series Скачать руководство пользователя страница 257 | Manualshive

Страница: 257 / 404

background image

1A-254 Engine Control System (4HK1)

DTC P1669 (Flash Code 75)

Circuit Description

The diesel particulate defuser (DPD) lamp is located on
the instrument panel (IP) cluster. The DPD lamp
informs the driver that an incomplete automatic
regeneration has occurred and manual regeneration is
required.
The ECM monitors the DPD lamp control circuit for
conditions that are incorrect for the commanded state
of the DPD lamp. For example, a failure condition
exists if the ECM detects low voltage when the DPD
lamp is commanded OFF, or high voltage when the
DPD lamp is commanded ON. If the ECM detects an
improper voltage level on the control circuit, this DTC
will set.

Condition for Running the DTC

• The battery voltage is between 18 to 32 volts.
• The ignition switch is ON.

Condition for Setting the DTC

Either of following condition is met:

• The ECM detects a low voltage condition on the

DPD lamp control circuit when the lamp is
commanded OFF.

• The ECM detects a high voltage condition on the

DPD lamp control circuit when the lamp is
commanded ON.

Action Taken When the DTC Sets

• The ECM will illuminate the SVS lamp. Refer to

DTC Type Definitions for Action Taken When the
DTC Sets - Type C.

Condition for Clearing the DTC

• Refer to DTC Type Definitions for Condition for

Clearing the SVS Lamp/ DTC - Type C.

Diagnostic Aids

• If an intermittent condition is suspected, refer to

Intermittent Conditions in this section.

Schematic Reference:

Engine Controls Schematics

Connector End View Reference:

Engine Controls

Connector End Views or ECM Connector End Views

Circuit/ System Testing DTC P1669

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check
- Engine Controls?

—

Go to Step 2

Go to Diagnostic

System Check -

Engine Controls

2

1.

Verify whether the instrument panel (IP)
cluster is operational.

2.

Install a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Turn ON the ignition for 40 seconds while
observing the DTC Information with a scan
tool.

Does the DTC fail this ignition?

—

Go to Step 3

Go to Diagnostic

Aids

3

1.

Turn OFF the ignition.

2.

Inspect the Meter (10A) fuse in the cab.

Is the Meter (10A) fuse open?

—

Go to Step 4

Go to Step 5

4

Replace the Meter (10A) fuse. If the fuse continues
to open, repair the short to ground on one of the
circuits that is fed by the Meter (10A) fuse or
replace the shorted attached component.

Did you complete the repair?

—

Go to Step 17

—

5

1.

Turn OFF the ignition.

2.

Disconnect the ECM J-14 harness connector.

3.

Turn ON the ignition, with the engine OFF.

Is the DPD lamp OFF?

—

Go to Sep 6

Go to Step 12

LG4HKED-WE-0871.book 254

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
255
256
257
258
259
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: Aalborg Страницы: 128

Бренд: Quectel Страницы: 23

Бренд: Quectel Страницы: 79

Бренд: Danfoss Страницы: 7

Бренд: Ebyte Страницы: 38

Бренд: EBS Страницы: 30

Бренд: Rain Bird Страницы: 4

Бренд: Rain Bird Страницы: 2

Бренд: Rain Bird Страницы: 140

WeatherSmart RSC600i

Бренд: Raindrip Страницы: 36

Бренд: Vaillant Страницы: 27

Бренд: Vaillant Страницы: 36

Бренд: Vaillant Страницы: 28

Бренд: Vaillant Страницы: 92

UTAdvanced UT35A

Бренд: YOKOGAWA Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды