Isuzu 2008MY N Series Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 404

background image

1A-118 Engine Control System (4HK1)

11

1.

Inspect for an intermittent and for poor
connections at the harness connector of the
ECT sensor (pins 1 and 2 of E-25).

2.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 15

Go to Step 13

12

1.

Turn OFF the ignition.

2.

Disconnect the ECM harness connector.

3.

Inspect for an intermittent and for poor
connections at the harness connector of the
ECM (pins 84 and 109 of E-12).

4.

Repair the connection(s) as necessary.

Did you find and correct the condition?

—

Go to Step 15

Go to Step 14

13

Replace the ECT sensor. Refer to ECT Sensor in
Section 1C Engine Cooling.

Did you complete the replacement?

—

Go to Step 15

—

14

Important:

Replacement ECM must be

programmed and learned.
Replace the ECM. Refer to ECM Replacement.

Did you complete the replacement?

—

Go to Step 15

—

15

1.

Reconnect all previously disconnected
harness connector(s).

2.

Clear the DTCs with a scan tool.

3.

Turn OFF the ignition for 30 seconds.

4.

Start the engine.

5.

Operate the vehicle within the Conditions for
Running the DTC. You may also operate the
vehicle within the conditions that you
observed from the Freeze Frame/ Failure
Records.

Did the DTC fail this ignition?

—

Go to Step 3

Go to Step 16

16

Observe the DTC Information with a scan tool.

Are there any DTCs that you have not
diagnosed?

—

Go to DTC List

System OK

Step

Action

Value(s)

Yes

No

LG4HKED-WE-0871.book 118

ページ

２００７年１１月２９日　木曜日　午後６時２９分

«
...
119
120
121
122
123
...
»

Содержание 2008MY N Series





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008MY N Series

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: Dantherm Страницы: 96

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: Eaton Страницы: 6

Бренд: J3C Страницы: 2

Бренд: Xilinx Страницы: 2

Бренд: Balboa Water Group Страницы: 88

Бренд: ABB Страницы: 2

Бренд: ZKTeco Страницы: 13

Бренд: UniPi Technology Страницы: 4

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: GBD Страницы: 60

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Бренд: McIntosh Страницы: 68

Бренд: Kelly Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды