manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 187

Test Setup - Test Configurator, Timer, and System

NetBlazer

175

MAC/IP/UDP

MAC 

Source MAC Address

 indicates the default and unique Media Access 

Control (MAC) address given to the Ethernet port. 

Destination MAC Address

: Enter the destination MAC address for the 

stream. The default setting is the source MAC address. The destination 
MAC Address field is not accessible when the 

Resolve MAC Address

 

check box is selected.

 

Resolve MAC Address

 check box, when selected (default), sends a 

request to the network to retrieve the MAC address corresponding to 
the selected destination IP address. This setting is coupled with the 

Resolve MAC Address

 check box from 

IP

 on page 178. This check box 

is not available when the 

Network Layer

 is set to 

None

 (refer to 

Modify 

Frame Structure

 on page 173). 

OAM Quick Ping

 button automatically starts the quick Ping utility for 

the stream destination MAC address and provides either a successful 
or failed result. The quick Ping uses 3 attempts, a delay of 1 second, 
and a Timeout of 5 seconds. 

EtherType

 is set to the following values by default and is configurable 

from 

0x0000

 to 

0xFFFF

 when the 

Network Layer

 is set to 

None

: 

0x0000

 when 

Network Layer

 is set to 

None

 

0x0800

 for IPv4 

0x86DD

 for IPv6 

0x8847

 for MPLS 

0x88B7

 when 

Network Layer

 is set to 

None

 with EtherBERT test. 

0x8902

 for S-OAM (available with EtherSAM) 

Note:

Depending on the 

Layer Mode

 (available with EtherSAM), some EtherType 

require to set the configuration parameters through the 

Modify Frame 

Structure

 pop-up instead of configuring its value from this field; in this case 

a pop-up message is displayed indicating the reason. The following 
EtherType are not supported for 

Mixed

 layer mode: 0x0001 to 0x05FF and 

0x8870. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды