manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 242

Test Setup - Test Configurator, Timer, and System

230

FTB-700G/800 Series

Services - Global

Services - Global 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, tap on the services 

block, the 

Global

 tab, and on the 

General

 button. 

General Button 

The following parameters are displayed and configurable per service. 

Check boxes: 

The first check box (top-left) allows to sequentially enable 
service(s) within the limit of the link capacity when the 

Service 

Performance Test

 is enabled or enable all services when the 

Service Performance Test

 is disabled. 

The check boxes next to the service numbers allow to enable each 
service individually. 

When the 

Service Performance Test

 is enabled, up to 10 services 

can be enabled one after the other, as long as the 

Total TX Rate

 

(bandwidth) is not reached (

Committed

). For example, if the first 

service is using the full bandwidth available, then no other service 
can be enabled. If the first enabled service uses half bandwidth, 
then at least another service can be enabled using up to half 
bandwidth. Thus, to enable a second service, first set the CIR value 
within the non-used bandwidth (

Available

), then enable it. 

When the 

Service Performance Test

 is disabled, up to 10 services 

can be enabled one after the other; the total TX rate is not limited.

Service Name

 indicates the name of each service. Tap on the 

Service 

Name

 button to modify the name of each service. See 

Services - Profile

 

on page 233

 

for more information. 

Direction

, available with 

Dual Test Set

, indicates results from local to 

remote (

L->R

) and remote to local (

R->L

). 

Frame Size

 indicates the frame size of each service. Tap on the 

Frame 

Size

 button to modify the frame size of each service. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды