EXFO FTB-1 Скачать руководство пользователя страница 204

Страница: 204 / 675

Test Setup - Test Configurator, Timer, and System

192

FTB-700G/800 Series

Network Details (iSAM)



Performance Test

check box when selected (default) verifies that the

SLA parameters (FD, IFDV, and FLR)

are met over time by running

multiple services simultaneously. Results are measured and compared
to the configured thresholds to declare the pass/fail verdicts. The

Performance Test

is only performed for services that have their

CIR

check box selected.

Set the

Performance Test

duration in hh:mm format: 1 minute to

24 hours (default is 10 minutes).



RFC 6349 Test on Service 1

check box when selected (cleared by

default) verifies that the Ethernet service is able to properly carry TCP
traffic;

Service 1

is used to performed the RFC 6349 test. Enabling the

RFC 6349 Test on Service 1

automatically set the operation mode to

DTS and the layer to

L3/L4

; direction is bidirectional, max MTU is 1500

bytes, multiple connections as well as Path MTU Discovery are
enabled.

Duration: The field next to the

RFC 6349 Test on Service 1

check box

is used to set the duration of the TCP Throughput phase per direction in
hh:mm format: 1 minute (default) to 24 hours.

Threshold (% of ideal)

allows to enter the TCP Throughput as a

percentage of the Ideal L4 Throughput that will be used to declare the
pass/fail verdict for both directions:

100

%; default is



Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды