manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 256

Test Setup - Test Configurator, Timer, and System

244

FTB-700G/800 Series

Signal (Transport)

TX Frequency 

TX Frequency (GHz)

 indicates the frequency (actual fre 

Frequency offset) used for transmission. 

Offset (ppm)

 check box, when selected (cleared by default), allows to 

set the frequency offset that will be generated. Use the “+” or “-” 
button to respectively increment or decrement the frequency offset 
value based on the defined 

Increment/Decrement Size

, or directly 

type the frequency offset value in the field. Possible offsets are: 

Note:

Frequency offset is not available when 

Through

 mode is selected.  

Interface

Frequency Offset

a

a.

The frequency offset range is guaranteed for a source signal at 0 ppm. In the event

that the source signal already has an offset, then the output signal may exhibit an

offset larger than the range specified.

Nominal Frequency

DS1

±140 ppm

1544000 bit/s

E1

± 70 ppm

2048000 bit/s

E3

± 50 ppm

34368000 bit/s

DS3

44736000 bit/s

STS-1e/STM-0e

51840000 bit/s

E4

139264000 bit/s

STS-3e/STM-1e

155520000 bit/s

OC-1/STM-0 

± 50 ppm

51840000 bit/s

OC-3/STM-1 155520000 

bit/s

OC-12/STM-4 622080000 

bit/s

OC-48/STM-16 2488320000 

bit/s

OC-192/STM-64 9953280000 

bit/s

OTU1 

± 50 ppm

2666057143 bit/s

OTU2 

± 50 ppm (Framed)
± 120 ppm (Unframed)

10709225316 bit/s

OTU1e 

± 120 ppm

11049107143 bit/s

OTU2e 11095727848 

bit/s

OTU1f 11270089286 

bit/s

OTU2f 11317642405 

bit/s

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды