manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 248

Test Setup - Test Configurator, Timer, and System

236

FTB-700G/800 Series

Services - Profile

The following table lists each component that may affect the minimum 
frame size value. 

Note:

Sending traffic with frame size > 1518 in switched network may results in 
losing theses frames. 

EMIX

 button is available when EMIX type is selected. The EMIX frame 

sequence is repeated until the test ends. 

Quantity

 allows to select from 2 to 8 frames size values (default is 

5

). 

EMIX Frame Sizes

 allows to set the EMIX frame sizes (default are 

64

, 

128

, 

512

, 

1024

, and 

1518

). The minimum frame size value is adjusted 

according to the frame structure and components selected as shown 
in the above table. 

Restore Default

 button reverts the quantity and EMIX frame sizes to 

their default values. 

Component

Description

VLAN

4 bytes per VLAN (up to 2 VLAN)

MPLS

4 bytes per label (up to two labels)

UDP

8 bytes

TCP

20 bytes

Ethernet Header

14 bytes

LLC and SNAP Headers

8 bytes

IPv4

20 bytes

IPv6

40 bytes

Using DTS

4 bytes

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды