manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 164

Test Setup - Test Configurator, Timer, and System

152

FTB-700G/800 Series

Interface (Ethernet, Packet Sync, Fibre Channel, and Wireless)

C&M Channel

 defines the kind of channel that will be used by the 

startup sequence for negotiation. 

Auto

 (default): Overhead byte #Z.66.0 can use any of the HDLC 

rates and Overhead byte #Z.194.0 can use any of the Ethernet 
Subchannel in the negotiation process. 

HDLC

: Only overhead byte #Z.66.0 is used with the configured 

HDLC Rate during the negotiation process. Ethernet #Z.194.0 byte 
is set to rr00 0000 as it is disabled. 

Ethernet

: Only overhead byte #Z.194.0 is used with the configured 

Ethernet Subchannel during the negotiation process. HDLC 
#Z.66.0 byte is set to rrrr r000 as it is disabled. 

Disabled

: Both HDLC Rates and Ethernet Subchannel are disabled 

to simulate a Passive Link. Ethernet #Z.194.0 byte is set to rr00 0000 
and HDLC #Z.66.0 byte is set to rrrr r000. Only available with 

Base 

Station

 emulation mode. 

C&M

 table indicates either the received (HDLC or Ethernet) or 

negotiated (Auto) C&M for Ethernet subchannel and HDLC rates in 
Mbit/s. A red background indicates either a C&M type mismatch or 
HDLC Rate/Ethernet subchannel mismatch compared to the generated 
C&M channel. An arrow is displayed indicating which C&M Channel 
should normally be selected as per the standard rules. 

Subchannel

 selects the Ethernet Subchannel number: 

20

 to 

63

 where 

63 is the lowest bit rate and 20 the highest. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды