manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 454

Test Results

442

FTB-700G/800 Series

Summary (Traffic Gen & Mon)

Out-of-Sequence

: See 

Streams - Frame Loss / Out-of-Sequence

 on 

page 388. 

Stream

 indicates the stream number and provides stream detailed 

statistics when tapping on its button. 

The following statistics are displayed for the selected stream.

Stream Selection: Select a stream by either using the left/right 
arrow or by tapping over the stream numbers area then tapping on 
a specific stream number. An orange background indicates the 
selected stream. 

Throughput

, 

Jitter

, and 

Latency

 meters display respectively the 

measured Throughput, Jitter, and Latency for the selected stream. 

Note:

The green region is delimited from 0 to the Threshold corresponding to a 

PASS

 verdict. The red regions beyond the threshold corresponds to a

 FAIL

 

verdict. The Pass/Fail verdict is only displayed when enabled (see 

QoS 

Metrics

 on page 272).

Jitter

: See 

Streams - Jitter

 on page 388. 

Latency

: See 

Streams - Latency

 on page 389.

RX Rate

: See 

Streams - Throughput

 on page 390.

RX Frame Count

 indicates the number of frame received 

matching the selected stream. 

TX Rate

: See 

Streams - Throughput

 on page 390.

TX Frame Count

 indicates the number of transmitted frames 

matching the selected stream. 

Frame Loss

 and 

Out-of-Sequence

: See 

Streams - Frame Loss / 

Out-of-Sequence

 on page 388.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды