manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 506

Test Functions

494

FTB-700G/800 Series

OH - SONET/SDH

M0 

or 

M1 (SDH) 

M0

: MS-REI. STM-1 channel #1 of a STM-0e and STM-0 signal. 

M1

:MS-REI. STM-1 channel #1 of a STM-1e and STM-1 signal; 

channel #3 of an STM-N signal (N>1). 

Undefined “--”

 for all other channels not covered by M0, and M1. 

E2

: Orderwire. Provides a 64 Kbit/s voice channel for communication 

between LTEs. This byte is only defined for the first STS-1/STM-1 frame 
of a composite signal. 

STS/AU/TU-3 

J1

: Trace. Available when the Trace format is set to 1 Byte (Refer to 

Traces (SONET/SDH)

 on page 284). 

SONET: The J1 Trace byte provides a 16 or 64 byte fixed string to verify 
connection between path transmitting equipment and path receiving 
equipment. 

SDH: The higher-order (AU)/low-order (TU) VC-N path trace byte 
provides a 64 byte fixed string to verify connection between path 
transmitting equipment and path receiving equipment.

B3

: BIP-8. The BIP-8 (Bit-Interleaved Parity) byte provides path error 

monitoring. The byte is calculated by performing a even-parity check 
over all bits of the previous SPE. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды